background image

A-2

[INSTALLATION PRECAUTIONS]

CAUTION

Do not bunch the control wires or communication cables with the main circuit 
or power wires, or install them close to each other.
They should be installed 100 mm (3.94 inch) or more from each other.
Not doing so could result in noise that may cause malfunction.

CAUTION

Use the programmable controller in the environment conditions given in the 
general specifications in the User's Manual for the CPU module. Failure to do 
so may cause an electric shock, fire, malfunction, or damage to or 
deterioration of the product.
While pressing the installation lever located at the bottom of the module, fully 
insert the module fixing projection into the fixing hole in the base unit to 
mount the module. Incorrect module mounting may cause a malfunction, 
failure, or drop of the module. In an environment of frequent vibrations or 
impacts, secure the module with screws.
The screws must be tightened within the specified torque range. If the screw 
is too loose, it may cause a drop or malfunction. Excessive tightening may 
damage the screw and/or the module, resulting in a drop or malfunction.
Be sure to shut off all phases of the external power supply used by the 
system before mounting or removing the module. Failure to do so may cause 
damage to the product.
Do not directly touch any conductive part or electronic part of the module.
Doing so may cause a malfunction or failure of the module.

Содержание Q68TD-G-H01





















Отзывы: