Mitsubishi NZ2EHF-T8 Скачать руководство пользователя страница 8

1. Before Using the Product 

 

 

7

 

 

1.

 

Before Using the Product 

This chapter provides information you should know before using the product. 

About the Unit 

NZ2EHF-T8 is an IEEE-802.3 (Ethernet)/IEEE-802.3u (Fast Ethernet)-compliant 8-port switching HUB 
unit, equipped with full-duplex communication support, AutoMDI/MDI-X feature, and auto-recognition 
function of communication rate (10/100Mbps) and communication method (half/full duplex) using the 
auto-negotiation feature. NZ2EHF-T8 uses Category 3, 5, 5e, or 6 UTP (unshielded twist pair) cables or 
STP (shielded twist pair) cables. For 100Mbps communication rate, use cables equal to or greater than 
Category 5.   
Please read this manual carefully so that you can build a system by connecting the switching HUB unit to 
external devices.   

Features 

The Auto MDI/MDI-X feature can automatically recognize the cable type, straight-through cable or 
crossover cable, to prevent problems using the wrong cable type.   
Also, the auto-negotiation feature can automatically recognize and choose the best communication 
rate (10/100Mbps) and method (half/full duplex) available.   

The unit is equipped with a 35mm DIN rail mounting mechanism as standard.   

The power connector includes an FG terminal. 

 

Environment 

Use this product in the following environment. If used under environmental conditions exceeding these 
ranges, the board may overheat, malfunction, or cause a failure. 

Operating ambient temperature 

0 to 50

°

C

 

Operating ambient humidity 

10 to 90%RH (No condensation)

 

Corrosive gases 

None 

Floating dust particles 

small amounts (non excessive)   

Содержание NZ2EHF-T8

























Отзывы: