Mitsubishi MELSEC iQ-R series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 86

background image

10

INTRODUCTION

Thank you for purchasing the Mitsubishi MELSEC iQ-R series programmable controllers.
This manual describes the performance specifications, procedures before operation, wiring, and operation examples of the
relevant products listed below.
Before using this product, please read this manual and the relevant manuals carefully and develop familiarity with the
functions and performance of the MELSEC iQ-R series programmable controller to handle the product correctly.
When applying the program and circuit examples provided in this manual to an actual system, ensure the applicability and
confirm that it will not cause system control problems.
Please make sure that the end users read this manual.

Unless otherwise specified, this manual provides program examples in which the I/O numbers of X/Y0 to X/YF
are assigned to the temperature control module. Assign I/O numbers when applying the program examples to
an actual system. For I/O number assignment, refer to the following.



MELSEC iQ-R Module Configuration Manual

Relevant products

R60TCTRT2TT2, R60TCTRT2TT2BW, R60TCRT4, R60TCRT4BW

COMPLIANCE WITH EMC AND LOW VOLTAGE

DIRECTIVES

Method of ensuring compliance

To ensure that Mitsubishi programmable controllers maintain EMC and Low Voltage Directives when incorporated into other
machinery or equipment, certain measures may be necessary. Please refer to one of the following manuals.
•



MELSEC iQ-R Module Configuration Manual

•



Safety Guidelines (This manual is included with the base unit.)

The CE mark on the side of the programmable controller indicates compliance with EMC and Low Voltage Directives.

Additional measures

To ensure that this product maintains EMC and Low Voltage Directives, please refer to one of the following manuals.
•



MELSEC iQ-R Module Configuration Manual

•



Safety Guidelines (This manual is included with the base unit.)

«
...
10
11
12
13
14
...
»

Содержание MELSEC iQ-R series























































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC iQ-R series

Бренд: ABB Страницы: 52

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

7000-2 - Escalade RAID Controller

Бренд: 3Ware Страницы: 2

Origami 4M-006-01

Бренд: 4 Moms Страницы: 28

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 2

Бренд: Camozzi Страницы: 64

BT300 BurnerTronic

Бренд: Lamtec Страницы: 48

Бренд: Watts Страницы: 4

Бренд: ZKTeco Страницы: 20

Бренд: ZKTeco Страницы: 8

Бренд: ZKTeco Страницы: 10

Бренд: ZKTeco Страницы: 121

Бренд: ZKTeco Страницы: 12

Бренд: ZKTeco Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды