manualshive.com logo in svg

Mitsubishi Heavy Industries FDCA Series, Техническое руководство

Поделиться
Скачать
Mitsubishi Heavy Industries FDCA Series Скачать руководство пользователя страница 153

-

 151 

-

11

Error display

:   

e49

[Abnormal low pressure or low pressure sensor wire disconnected]
 (Only case of FDCA801, 1001 type)

Indoor unit

Red LED

Green LED

Stays OFF

Keeps flashing

Red LED

Green LED

1 time flash

Keeps flashing

Outdoor unit

YES

NO

NO

NO

Correction

Replacement low

pressure sensor

Change of outdoor

unit PCB

Is the low pressure sensor 

connector’s connection 

(sensor side, PCB side) OK?

Did it retun to normal?

Is the amount of refrigerant appropriate?
Is the refrigeration circuit abnormal?

CM operation

CM stop

Low pressure (Mpa)

0.079 (0.120)

0.128

    Abnormal pressure detection

●

Display Conditions
The compressor stops if the low pressure sensor detects a pressure of 0.079 (0.120) MPa or lower con-
tinuously for 15 seconds.
After a 3-minute delay, the compressor restarts, but if this occurs 3 times within 60 minutes.

[Gas low error] (Only case of FDCA801, 1001 type)

Indoor unit

Red LED

Green LED

Stays OFF

Keeps flashing

Red LED

Green LED

1 time flash

Keeps flashing

Outdoor unit

YES

Is E52

       Cooling operation

     E52      Heating operation

displayed in the remote

controller’s

screen?

The 52C is abnormal.

12

Indoor unit

Red LED

Green LED

Stays OFF

Keeps flashing

Red LED

Green LED

Lights contiously

Keeps flashing

Outdoor unit

Error display :   

e52

Note (1)  Values in (  ) show in the case where 10 minutes or longer have passed since the compressor started.

Is the service valve fully open?

Are the 

indoor heat exchanger and return 

air temperature thermistor connector 

connections OK?

Are the 

characteristics of the indoor heat 

exchanger and return air temperature 

thermistors OK?

 Is the low pressure during 

operation appropriate?

Open it fully.

NO

YES

NO

YES

YES

NO

YES

NO

Indoor control PCB is faulty.     Replace it.
(Indoor heat exchanger and return air tem-
perature thermistors input circuits are faulty.)

Correction

Charge with refrigerant.

The indoor heat exchanger and 
return air temperature thermistor 
are faulty.       Replace them.

Temperature (

°

C)

15

10

5

0

10

30

40

20

50

5k

Ω

 at 25

°

C

Indoor unit heat exchanger
thermistor (Th

I-

R), 

Return air thermistor (Th

I-

A)

Resistance temperature characteristics

Resistance

(k

Ω

)

[52C Abnormal]

Содержание FDCA Series




































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды