Mitsubishi Heavy Industries FDCA Series Скачать руководство пользователя страница 149

Страница: 149 / 163

147

[Open phase at L3 phase of 52C secondary side]

Indoor unit

Red LED

Green LED

Stays OFF

Keeps flashing

Red LED

Green LED

1 time flash

Keeps flashing

Outdoor unit

Notes (1) Also check if there is voltage at the L3 phase on the 52C primary

side, but no voltage on the secondary side (coil wire disconnec-

tion or faulty contacts).

(2) If there is voltage at the L3 phase on the 52C primary side and it

is not abnormal, the outdoor unit control PCB is faulty.

Error display :

e34

Error display

e33

[Compressor overcurrent trouble]

Indoor unit

Red LED

Green LED

Stays OFF

Keeps flashing

Red LED

Green LED

1 time flash

Keeps flashing

Outdoor unit

YES

Is the voltage

AC220/240V between the

L1 and L3 phases and between the L2

and L3 phases on the 52C

secondary side?

Is there overcurrent

at the compressor?

Out of phase between the

L1 and L2 phases.

Check the unit side.

• Compressor is faulty. Replace

• 52C is faulty.
• There is a disconnection between

52C and CM or in the L1 and L2
phases between TB1 and 52C.

• During cooling: Is FMo turning?
• During heating: Is FM

turning?

Is the service valve (gas side) fully open?
Is the filter clogged?

• Is there an overcharge?
• Is the installation space for the indoor and

outdoor units proper?

• Is there a short circuit in the indoor or outdoor units?

(1)

Outdoor unit control PCB is
faulty. Replace
(The CT input circuit is faulty.)

• Is the power supply voltage proper? (Isn’t it too low?)

• Are the power lines proper? (Aren’t they too thin?)

• Is the overcurrent setting correct?

(1)

• Is the compressor running with an overload?

• Is the compressor locked?

Notes (1) Measure the overcurrent value to make sure. (Models FDCA301~601 only)

Also make sure the overcurrent setting set with SW3 and SW4-1 on the outdoor unit control PCB

is not incorrect.

52C

secondary side L3 phase

open?

Repair

YES

The outdoor unit control PCB is faulty.
(The CT circuit is faulty) Replace

(1)

(2)

Only case of FDCA301~601
If the unit is operated with the service valve closed, 49C (internal ther-
mostat) operates. E34 may also be displayed. Check the service valve.

Содержание FDCA Series




































































































































































Результаты поиска

Содержание FDCA Series

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Heavy Industries FDCA Series, Техническое руководство

Результаты поиска

Содержание FDCA Series

Отзывы:

Бренды по названию

Популярные бренды