Mitsubishi Electric PUMY-P125VMA Скачать руководство пользователя страница 24

Страница: 24 / 92

8-3. SYSTEM CONTROL

8-3-1. Operating a Single Refrigerant System

When operating either alone or as part of a group, a M-NET remote controller (NR) may be used to control a single

refrigerant system that does not overlap with any other system.

<Example of system arrangement>

Using a M-NET remote controller (NR)

✽

Address setting must be performed.

✽

The NR wire and indoor and outdoor transmission wires must be a non-polar two wire cable.

✽

One NR may be connected to a maximum of 16 indoor unit.

✽

Two NR units may be used to perform control tasks (the second one pressed will have priority if two are pressed

simultaneously).

✽

For the system utilizing R-Converter units (PAC-SF29LB), the following systems are not available. Group operation

system, centralized controller, group remote controller, etc. (See the installation manual of R-Converter units.)

For indoor-outdoor
transmission wire

Remote
control wire

indoor-outdoor trnasmission cable

2 remote controllers

Group operation (maximum
16 indoor units)

Outdoor
unit

Indoor unit

Remote controller
network

Indoor unit

✽

If the user plans to install multiple refrigerant

systems and a centralized controller in the

future, it is strongly suggested that a NR be

used.

OC272A--1.qxp 03.9.4 11:06 AM Page 24

Содержание PUMY-P125VMA





























































































Результаты поиска

Содержание PUMY-P125VMA

Отзывы:

Похожие инструкции для PUMY-P125VMA

Бренды по названию

Популярные бренды

Mitsubishi Electric PUMY-P125VMA, Техническое и сервисное руководство

Результаты поиска

Содержание PUMY-P125VMA

Отзывы:

Похожие инструкции для PUMY-P125VMA

Бренды по названию

Популярные бренды