Mitsubishi Electric PEH-P10YE Скачать руководство пользователя страница 25

Страница: 25 / 28

–23–

Test run start and finish

• Operation from the indoor unit

Execute the test run using the installation manual for the indoor unit.

• Operation from the outdoor unit

Execute settings for test run start, finish and operation mode (cooling, heating) using the DIP switch SW 4 on the outdoor

substrate.

OFF

<SW4>

1
2

A
B

C
D

Set the operation mode (cooling, heating) using SW 4-2

Turn ON SW 4-1, The operation mode for SW 4-2 will be adhered to, and the test run will commence

Turn OFF SW 4-1 to finish the test run

• There may be a faint knocking noise emitted from the proximity of the fan during the test run. This is torque fluctuation

occurring due to control of fan revolutions. There is no problem with the product.

Note:

The SW 4-2 operation mode cannot be changed during the test run. (To change test run mode, stop the equipment with SW

4-1, change the operation mode, then restart test run with SW 4-1.)

Change to self-diagnosis mode

Press the CHECK button twice within three seconds to show the

following display.

Select the refrigerant address number to be self-diagnosed

Press the

buttons to scroll through the refrigerant ad-

dress numbers (00 to 15) and select the refrigerant address num-

ber to be self-diagnosed. After three seconds from making the

change, the lit refrigerant address to be self-diagnosed will start to

flash, and self-diagnosis will commence.

Self-diagnosis result display

See the above chart for details of error code contents.

(1) When there is an error history

a) Alternating display
b) Error code
c)

Attribute of error search

d) Unit number

(2) When there is no error history

[3] Self-diagnosis

Use the remote controller to look up each units error history.

STAND BY
DEFROST

INDOOR UNIT

ADDRESS NO

CLOCK

ON OFF

˚C

1Hr.

˚C

CHECK MODE

FILTER

CHECK

FUNCTION

STAND BY
DEFROST

INDOOR UNIT

ADDRESS NO

CLOCK

ON OFF

˚C

1Hr.

˚C

CHECK MODE

FILTER

CHECK

FUNCTION

STAND BY
DEFROST

INDOOR UNIT

ADDRESS NO

ERROR CODE

CLOCK

ON OFF

˚C

1Hr.

˚C

CHECK MODE

FILTER

CHECK

FUNCTION

STAND BY
DEFROST

INDOOR UNIT

ADDRESS NO

CLOCK

ON OFF

˚C

1Hr.

˚C

CHECK MODE

FILTER

CHECK

FUNCTION

(1)

STAND BY
DEFROST

INDOOR UNIT

ADDRESS NO

ERROR CODE

CLOCK

ON OFF

˚C

1Hr.

˚C

CHECK MODE

FILTER

CHECK

FUNCTION

(2)

Stop

Cooling

Operation

Heating

Содержание PEH-P10YE





























Результаты поиска

Содержание PEH-P10YE

Отзывы:

Похожие инструкции для PEH-P10YE

Бренды по названию

Популярные бренды

Mitsubishi Electric PEH-P10YE, Техническое и сервисное руководство

Результаты поиска

Содержание PEH-P10YE

Отзывы:

Похожие инструкции для PEH-P10YE

Бренды по названию

Популярные бренды