PD-5065
18
1. Power failure
(1) Power failure
YES
YES
The power cord is
defective.
The MAIN PWB is fault.
YES
YES
YES
NO
YES
NO
Connect the power cord.
Disconnect the power cord.
YES
(1)The power supply is
not turned on.
NO
NO
NO
NO
The power unit is
fault.
YES
NO
YES
NO
YES
NO
YES
NO
(Caution) If any abnormality is sensed in such a manner that the LED flashes
or lights, all the power lines other than those of 7Vdc (M+7V) and
5Vdc (M+5V) are automatically turned off in about 10 seconds.
When checking the power lines other than those of M+7V and
M+5V, a circuit tester or the like should have been connected in
advance. Is the AC power output available at the AC connector
(2) Blinking in green
(Alarm of temperature
sensor error or fan
error)Go to (P19, P20 )
(3) Blinking in red after
repeating reciprocal flash
in red and green (POWER
ON OFF) 3times (Alarm of
temperature error) Go to
(P21).
(4) Alternation blinking in
red and green (Alarm of
panel error) Go to
(P22).
(5) Lighting in green, and
then in red (Alarm of
power line error) Go to
(P23).
Is a 5Vdc output available in the state
that the LD connector is disconnected
and the main power is turned ON?
The LD connector
or the LED PWB is
fault.
Is a 5Vdc output available in the
state thatthe RS connector is
disconnected and the main power is
turned ON?
The RS connector or
the 232C PWB is
fault.
The PW connector, or the MAIN PWB
is fault.
Is a 5Vdc output available at
Pin
4
of the PW connector?
Is a 4.9Vdc output
available at Pin
3
of the
PM connector?
The PM connector or
the MAIN PWB is
fault.
Is a 6.8Vdc output available at
Pin
6
of the PM connector?
The PW connector is
fault.
Is a 6.8Vdc output available at
Pin
1
of the PW connector?
Is a 6.8Vdc output
available at Pin
1
of the
PM connector?
Is the AC power output
available at the AC connector
(power cord)?
Is the POWER/STANDBY
lamp lit?
Is a 6.8Vdc output available in the state
that the PW connector is disconnected
and the main power is turned ON?
The PW connector is
fault.
Is a 6.8Vdc output available in the state
that the PM connector is disconnected
and the main power is turned ON?
The PM connector or
the MAIN PWB is
fault.
Is a 6.8Vdc output available in the
state that the LD connector is
disconnected and the main power is
turned ON?
The LD connector
or the LED PWB is
fault.
NO
YES
NO
2.2 DIAGNOSIS
Содержание PD-4265
