background image

4

4. OUTDOOR UNIT INSTALLATION

4-1

INSTALLING THE UNIT

• Be sure to fix the unit’s legs with bolts when installing it.
• Be sure to install the unit firmly to ensure that it does not

fall by an earthquake or a gust.

• Refer to the figure in the right for concrete foundation.

Note:
The length of anchor bolts should be within 25 mm from
each anchor leg.

• Do not use the drain socket and the drain cap in the cold

region.
Drain may freeze and it makes the fan stop.

 CAUTION:

Be sure to carry out drain piping work following the in-
stallation manual.
If there is some deficiency in draining and piping work, it
may cause a risk of dripping from the unit, wetting or
forling your property.

4-2

MOUNTING ARRANGEMENT OF DRAIN SOCKET

 CAUTION:

Do not use drain socket and drain cap in the cold region.
Drain may freeze and it makes the fan stop.

1

Please choose one hole to discharge drain and install the drain socket to the hole.

2

Please close the rest of the holes with the drain caps.

3

Please connect a vinyl hose of 25 mm in the inside diameter on the market with the drain socket and lead
drain.

4-3

HOW TO REMOVE THE SERVICE PANEL AND THE CONNECT COVER

• Remove the four service panel securing screws, and pull

the panel down in an arrow direction to remove the service
panel.

• Remove the four connect cover securing screws to remove

the connect cover.

FREE SPACE REQUIRED AROUND OUTDOOR UNIT (Unit: mm)

500 or more

100 or more

200 or more

350 or more

100 or more

500 or more

1. Top side obstacles

When there is an obstacle behind the rear side only,
it does not matter if there is an obstacle over the
top side as shown in the figure below.

2. Front (blowing) side open

As long as space like the one shown in the figure
can be maintained, it does not matter if there are
obstacles in three direciton (but top side is open).

3. Obstacles on front (blowing) side only

In this case, the rear, both sides and top should be
open.

4. Obstacles on front and rear side only

The unit can be used by attaching an optional out-
door blowing guide (MAC-855SG) (but both sides
and top are open).

100 or more

500 or more

Blowing guide (MAC-855SG)

100 or more

500 or more

100 or more

Service space

350 or more

500 or more

;;;;

;;;;

5. Service space

Keep the service space as shown in the figure be-
low for maintenance.

500

330

Service panel

Fix here with
M10 bolts.

Make the setting
depth deeper.

Make with wider.

Anchor leg

25 mm or less

Anchor both length

Anchor both pitch

(Unit: mm)

Connect
cover

Содержание MXZ-A26













Отзывы: