Mitsubishi Electric MSZ-LN18VGB-E1 страница 47 Скачать руководство пользователя

Страница: 47 / 48

OPERATING PROCEDURE

PHOTOS/FIGURES

8. Removing the air purifying device

(Photo 8, 18)

(1) Remove the front panel, the outer vanes (R) (L)(hori-

zontal), the panels (U) (R) (L) (F), the corner box (R),
V.A. clamp and the electrical cover.

(2) Remove the lead wires from the water cover.
(3) Disconnect the following connector (Photo 8):

CN1T1 (Air purifying device)

(4) Remove the screw of the air purifying device support.
(5) Remove the air purifying device support.

9. Removing the line flow fan, the indoor fan motor

assembly, the indoor coil thermistor, and the
heat exchanger (Photo 4, 18, 19, 20, 21, 22)

(1) Remove the front panel, the outer vanes (R) (L)(hori-

zontal), the panels (U) (R) (L) (F), and the corner
boxes (R) (L), Wi-Fi interface, DISPLAY and i-see
SENSOR ASSEMBLY, the electrical box, the nozzle
assembly and the air purifying device.

(2) Loosen the screw inside the right side of the line flow

fan (Photo 19).

(3) Remove the 3 screws of the fan motor assembly.

Pull the fan motor assembly slightly toward you, and
remove it by pulling to the right (Photo 20).

(4) Remove the indoor coil thermistor from the heat

exchanger.

(5) Remove the 2 screws of the hairpin holder on the left

side of the heat exchanger. Raise the left side of the
heat exchanger, and pull the line flow fan to the lower
left to remove (Photo 21).

(6) Disengage the 2 catches on the right side of the heat

exchanger, and remove the heat exchanger (Photo 22).

*1 When attaching the line flow fan, screw the line flow

fan so 4 mm gap is provided between the right end of
the line flow fan and the right wall of the air passage
of the box (Figure 1).

Fan motor

Screw of the line fl ow fan

Heat exchanger

Photo 19

Photo 20

Heat exchanger

Hairpin holder

Screws of
the left side
of the heat
exchanger

Photo 21

Remove the heat exchanger
while slightly raising
and pulling it outward to
disengage the catches.

Catches

Photo 22

Screws of
the earth
plate

Catch of
water cover

Screw of the air purifying
device support

Figure 1

4 mm

Photo 18

Fan motor assembly

Screws of the fan motor assembly

OBH766B

Содержание MSZ-LN18VGB-E1

















































Результаты поиска

Содержание MSZ-LN18VGB-E1

Отзывы:

Похожие инструкции для MSZ-LN18VGB-E1

Бренды по названию

Популярные бренды

Mitsubishi Electric MSZ-LN18VGB-E1, Руководство по обслуживанию

Результаты поиска

Содержание MSZ-LN18VGB-E1

Отзывы:

Похожие инструкции для MSZ-LN18VGB-E1

Бренды по названию

Популярные бренды