manualshive.com logo in svg

Mitsubishi Electric MSZ-LN18VGB-E1, Руководство по обслуживанию, Страница: 46 / 48

Поделиться
Скачать
Mitsubishi Electric MSZ-LN18VGB-E1 Скачать руководство пользователя страница 46

OPERATING PROCEDURE

PHOTOS/FIGURES

7. Removing the vane motor units (L) (R) (vertical) 

and the vane motors (horizontal)

(1) Remove the front panel, the outer vanes (R) (L)

(horizontal), the inner vanes (R) (L), the vane slide 
assembly, the panels (U) (R) (L) (F), the corner boxes 
(R) (L), Wi-Fi interface, DISPLAY and i-see SENSOR 
ASSEMBLY, V.A. clamp, and the electrical cover.

(2) Remove the panel (F) (Photo 3).
(3) Remove the following connector (Photo 8):
 

<Indoor electronic control P.C. board>

 

CN151 (Vane motors)

(4) Pull out the drain hose from the nozzle assembly. Pull 

and remove the nozzle assembly (catches on left, 
right, and center) (Photo 10).

(5) Cut off the cable tie to secure the lead wires on the 

right side of the nozzle assembly (Photo 12).

(6) Remove the tape to secure the lead wires and the 

aluminum tape on the front of the nozzle assembly. 
(Photo 11)

Removing the vane motor (R) (horizontal) and the vane 
motor (horizontal) (Photo 14, 15)

(7) Remove the 3 screws of the vane motor unit (R) (hori-

zontal) and remove the lead wires of the vane motor  
(R) (vertical), the vane motor(R) (horizontal) and the 
vane motor (horizontal).

(8) Remove the 2 screws of the vane motor (R) (horizontal) 

from the backside of the vane motor unit (R) (horizon-
tal), and remove the vane motor (R) (horizontal).

(9) Remove the 2 screws of the vane motor (horizontal) 

from the backside of the vane motor unit (R) (horizon-
tal), and remove the vane motor (horizontal).

Removing the vane motor unit (R) (vertical) (Photo 15)

(10) Disengage the link of the vane motor unit (R) (vertical).
(11) Remove the screw indicated in , and remove the vane 

motor unit (R) (vertical).

Removing the vane motor (L) (horizontal) (Photo 16)

(12) Disengage the link of the vane motor unit (L) (vertical).
(13) Remove the 3 screws indicated in (Photo 16).
(14) Remove the 2 screws of the vane motor (L) (horizontal) 

from the backside of the vane motor unit (L) (horizon-
tal), and remove the vane motor (horizontal).

Removing the vane motor unit (L) (vertical) (Photo 17)

(15) Disengage the catch of the vane motor unit (L) (verti-

cal), and remove the vane motor unit (L) (vertical).

46

Photo 15   Vane motor unit (R) (vertical)

Vane motor unit (R) (vertical)

Link

Screw of vane motor 
(R) (vertical)

Photo 16

Vane motor unit (L) (vertical)

Link

Photo 17   Vane motor unit (L) (vertical)

Screws of the vane motor 
(L) (horizontal) on backside

Catch

Screws

Vane motor 
(L) (horizontal)

Detach the vane motor units (L) (horizontal and 
vertical). Then move them to the direction of     , 
and remove the link of the vane motor unit (L) 
(vertical).

Photo 14

Vane motor (R) 
(horizontal)

Screws of the vane motor 
(horizontal) on back side

Vane motor (horizontal) with a 
motor on backside

Vane motor unit (R) 
(horizontal)

Screws of the vane motor (R) 
(horizontal) on backside

Screws

Vane motor unit (L) 
(horizontal)

OBH766B

Содержание MSZ-LN18VGB-E1

















































Отзывы:

Нет отзывов