Mitsubishi Electric MSZ-LN18VGB - E1 Скачать руководство пользователя страница 42

Страница: 42 / 50

OPERATING PROCEDURE

PHOTOS/FIGURES

3. Removing the indoor electrical box
(Photos 4, 5, 6, 7, 8)

(1) Remove the front panel, the outer vanes (R) (L) (hori-

zontal), and the panels (U) (R) (L) (F) (refer to 1).

(2) Remove the lead wires of indoor coil thermistor, lead

wires of air purifying device, and cable of Wi-Fi inter-
face from the water cover (Photo 4).

(3) Remove the 2 screws of the CLR earth plate.
(4) Disengage the catches of the water cover, and

remove the water cover.

(5) Remove the corner box (R) (Photo 5).
(6) Remove the screw of the V.A. clamp, and remove the

V.A. clamp (Photo 4).

(7) Remove the screw of the electrical cover, and remove

the electrical cover (Photo 6).

(8) Disconnect the following connectors (Photo 8):

CN1J1 (DISPLAY AND i-see SENSOR ASSEMBLY)

CN2T1 (Limit switch)

(9) Remove the DISPLAY AND i-see SENSOR

ASSEMBLY (Photo 7).

(10) Disconnect the following connector (Photo 8):

CN110 (Wi-Fi interface)

(11) Remove the Wi-Fi interface (refer to 2).
(12) Remove the screw of the electrical box (Photo 7).
(13) Disconnect the following connectors (Photo 8):

CN211 (Indoor fan motor)

CN151 (Vane motors)

CN112 (Indoor coil thermistor)

CN1T1 (Air purifying device)

(14) Remove the electrical box.

Photo 5

Corner box (L)

Corner box (R)

Photo 7

Screw of the
electrical box

Remove the DISPLAY AND
i-see Sensor ASSEMBLY to
the direction of .

DISPLAY AND i-see
SENSOR ASSEMBLY

(Refer to Photo 11)

Photo 6

Screw of the
electrical cover

Electrical cover

Screws of the
CLR earth plate

Screw of the
terminal block

OBH766B

Содержание MSZ-LN18VGB - E1



















































Результаты поиска

Содержание MSZ-LN18VGB - E1

Отзывы:

Похожие инструкции для MSZ-LN18VGB - E1

Бренды по названию

Популярные бренды

Mitsubishi Electric MSZ-LN18VGB - E1, Руководство по обслуживанию

Результаты поиска

Содержание MSZ-LN18VGB - E1

Отзывы:

Похожие инструкции для MSZ-LN18VGB - E1

Бренды по названию

Популярные бренды