5-3. PUMPING DOWN
When relocating or disposing of the air conditioner, pump down the system following the procedure below so that refrigerant is not released into the atmosphere.
1) Connect the gauge manifold valve to the service port of the stop valve on the gas pipe side of the outdoor unit.
2) Fully close the stop valve on the liquid pipe side of the outdoor unit.
3) Close the stop valve on the gas pipe side of the outdoor unit almost completely so that it can be easily closed fully when the pressure gauge shows 0 psi [Gauge] (0 Mpa).
4) Start the emergency COOL operation.
To start the emergency operation in COOL mode, disconnect the power supply plug and/or turn off the breaker. After 15 seconds, connect the power supply plug and/or turn on
the breaker, and then press the E.O. SW once. (The emergency COOL operation can be performed continuously for up to 30 minutes.)
5) Fully close the stop valve on the gas pipe side of the outdoor unit when the pressure gauge shows (0.1 to 0 psi [Gauge] (0.05 to 0 Mpa)).
6) Stop the emergency COOL operation.
To stop operation, press the E.O. SW several times until all LED lamps turn off. Refer to operating instructions for details.
5-2. REMOVING THE INDOOR UNIT
Remove the bottom of the indoor unit from the installation plate. (Fig. 1, 2)
• Remove the panel assembly. (Refer to 5-1)
,QVHUWÀDWVFUHZGULYHUVLQWRWKHVTXDUHKROHVDWWKHOHIWDQGULJKWERWWRPRIWKHLQGRRU
unit and push them up; the bottom of the indoor unit goes down and the hooks are
released.
*1 Remove the screw.
*2 Remove the tab of corner box from the indoor unit, and pull the corner box.
*3 Pull the indoor unit to remove.
Square hole
Push Lower
Corner box
Fig. 1
Fig. 2
When pumping down the refrigerant, stop the compressor before disconnecting the refrigerant pipes. The compressor may burst if air etc. get into it.
WARNING
HEAD OFFICE: TOKYO BUILDING, 2-7-3, MARUNOUCHI, CHIYODA-KU,
TOKYO 100-8310, JAPAN
CN105
6. CONNECTING THE INTERFACE/CONNECTOR CABLE TO THE AIR CONDITIONER
Fix the connecting cable at the prescribed position securely. Incorrect installation
PD\FDXVHHOHFWULFVKRFN¿UHDQGRUPDOIXQFWLRQ
WARNING
• Connect the INTERFACE/CONNECTOR CABLE to the Indoor electronic control P.C. board of the air conditioner with the connecting cable.
• Cutting or extending the connecting cable of the INTERFACE/CONNECTOR CABLE results in defects in connecting.
Do not bundle the connecting cable together with power supply cord, indoor/outdoor connecting wire, and/or earth wire. Keep as much distance as possible between the
connecting cable and those wires.
• The thin part of the connecting cable should be stored and placed where customers cannot touch it.
Air conditioner
Thin part of the connecting cable.
Place this part where customers cannot touch it.
Thick part of the connecting cable
Indoor electronic
control P.C. board
CN105 for INTERFACE
Connecting
1
Remove the panel and the lower right corner box.
2
Open the covers of the Indoor electronic control P.C. board.
3
Connect the connecting cable to CN105 on the Indoor electronic control P.C. board.
4
Attach the cable clamp provided with Interface to the thick part of the connecting
FDEOHZLWKDVFUHZîDVVKRZQLQWKH¿JXUH
5
3DVVWKHFRQQHFWLQJFDEOHWKURXJKWKHULEDVVKRZQLQWKH¿JXUH
6
Close the covers of the Indoor electronic control P.C. board. Be careful not to catch
the thin part of the connecting cable in the cover. Reinstall the panel and the lower
right corner box.
