background image

14

 Caution:

•   Perform grounding.

Do not connect the ground wire to a gas pipe, water pipe arrester or tel

-

ephone ground wire. Defective grounding could cause an electric shock.

•  Do not install the unit in a place where an inflammable gas leaks.

If gas leaks and accumulates in the area surrounding the unit, it could cause 

an explosion.

•  Install a ground leakage breaker depending on the installation place (where 

it is humid).

If a ground leakage breaker is not installed, it could cause an electric shock.

•  Perform  the  drainage/piping  work  securely  according  to  the  installation 

manual.

If there is a defect in the drainage/piping work, water could drop from the 

unit and household goods could be wet and damaged.

•  Fasten a flare nut with a torque wrench as specified in this manual.

When  fastened  too  tight,  a  flare  nut  may  broken  after  a  long  period  and 

cause a leakage of refrigerant.

2.1. Outdoor unit

•  R32 is heavier than air—as well as other refrigerants—so tends to accumulate at 

the base (in the vicinity of the floor). If R32 accumulates around base, it may reach 

a flammable concentration in case room is small. To avoid ignition, maintaining a 

safe work environment is required by ensuring appropriate ventilation. If a refrig-

erant leak is confirmed in a room or an area where there is insufficient ventilation, 

refrain from using of flames until the work environment can be improved by ensur-

ing appropriate ventilation.

•  Where it is not exposed to strong wind.

•  Where airflow is good and dustless.

•  Where it is not exposed to rain and direct sunshine.

•  Where neighbours are not annoyed by operation sound or hot air.

•  Where rigid wall or support is available to prevent the increase of operation sound 

or vibration.

•  Where there is no risk of combustible gas leakage.

•  When installing the unit at a high level, be sure to fix the unit legs.

•  Where it is at least 3 m away from the antenna of TV set or radio. (Otherwise, 

images would be disturbed or noise would be generated.)

•  Please install it in an area not affected by snowfall or blowing snow. In areas with 

heavy snow, please install a canopy, a pedestal and/or some baffle boards.

•  Install the unit horizontally.

•  Refrigerant pipes connection shall be accessible for maintenance purposes.

/

  Install outdoor units in a place where at least one of the four sides is open, and in 

a sufficiently large space without depressions. (Fig. 2-1)

 Caution:

Avoid the following places for installation where air conditioner trouble is li

-

able to occur.

•  Where there is too much machine oil.

•  Salty environment as seaside areas.

•  Hot-spring areas.

•  Where sulfide gas exists.

•  Other special atmospheric areas.

The outdoor unit produces condensate during the heating operation. Select 

the installation place to ensure to prevent the outdoor unit and/or the grounds 

from being wet by drain water or damaged by frozen drain water.

2. Selecting the installation location

Fig. 2-1

OK

OK

OK

NG

1. The following should always be observed for safety

VH79A008H01_En.indd   14

2018/10/05   10:12:09

Содержание Mr.Slim SUZ-M-VA-ER Series
















Отзывы: