Function
Settings
Setting No.
Filter sign
100h
2500h
"Clean the filter" indicator is not displayed
Air flow
Quiet
(Fan speed)
Standard
High ceiling
No.of air outlets
4 directions
3 directions
2 directions
Optional high efficiency
Not supported
filter
Supported
Vane setting
No vanes (Vane No.3 setting : PLA only)
Vane No.1 setting
Vane No.2 setting
Optional humidifier
Not supported
(PLA only)
Supported
Vane differential setting
No.1 setting (TH5: 75–
Û)>
–28
:
])
in heating mode
No.2 setting (Standard, TH5: 82–
Û)>
–32
:
])
(cold wind prevention)
No.3 setting (TH5: 90–100
Û)>
32-38
:
])
Swing
Set temperature in heating
mode (4 degC up)
Fan speed when the
Extra low
heating thermostat is OFF
Stop
Keeping fan speed set by remote controller
Fan speed when the
Keeping fan speed set by remote controller
cooling thermostat is OFF
Stop
Detection of abnormality of
Detect
07
(107)
08
(108)
09
(109)
10
(110)
11
(111)
13
(113)
14
(114)
23
(123)
24
(124)
25
(125)
27
(127)
28
(128)
the pipe temperature (P8)
Neglect
1
2
3
1
2
3
1
2
3
1
2
1
2
3
1
2
1
2
3
1
2
1
2
1
2
3
1
2
1
2
Not available Swing
Available
Wave air flow
Available
Not available
}
PLA-BA
: Initial setting (Factory setting)
- : Not available
4-Way
cassette
PLA-BA
Ceiling
Suspended
PCA-KA
-
-
-
-
-
Mode No.
Wired remote controller
(RF thermostat)
Cealing
concealed
PEAD-AA
-
-
-
-
-
-
-
-
Refer to
the <Table 5>
below.
-
-
-
-
-
Refer to
the <Table 5>
below.
)XQFWLRQVDYDLODEOHZKHQVHWWLQJWKHXQLWQXPEHUWRRU$/LQWKHFDVHRIWKH,5ZLUHOHVVUHPRWHFRQWUROOHU
:KHQVHWWLQJIXQFWLRQVIRUDQLQGRRUXQLWLQDQLQGHSHQGHQWV\VWHPVHWWKHXQLWQXPEHUWRUHIHUULQJWR
4
VHWWLQJWKH
LQGRRUXQLWQXPEHU
:KHQVHWWLQJIXQFWLRQVIRUDVLPXOWDQHRXVWZLQLQGRRUXQLWV\VWHPVHWWKHXQLWQXPEHUWRWRIRUHDFKLQGRRU
XQLWLQFDVHRIVHOHFWLQJGLIIHUHQWIXQFWLRQVIRUHDFKXQLWUHIHUULQJWR
4
VHWWLQJWKHLQGRRUXQLWQXPEHU
:KHQVHWWLQJWKHVDPHIXQFWLRQVIRUDQHQWLUHVLPXOWDQHRXV7ZLQLQGRRUXQLWV\VWHPVHWUHIULJHUDQWDGGUHVVWR$/
LQWKHFDVHRIWKH,5ZLUHOHVVUHPRWHFRQWUROOHUUHIHUULQJWR
4
VHWWLQJWKHLQGRRUXQLWQXPEHU
7DEOH!$YDLODEOHIXQFWLRQVDQGVHWWLQJV
External static
pressure
Setting No.
Initial setting
(Factory setting)
35Pa
50Pa
70Pa
100Pa
150Pa
2
3
1
2
3
Mode No. 08 Mode No. 10
1
1
2
2
2
<Table 5> Mode No. 08 and 10
<Table 4> Mode No.11
Setting No.
Settings
PLA-BA
1
Vane No.3 setting
( Downward position than the standard )
Less smudging
2
Vane No.1 setting
Standard
3
Vane No.2 setting
( Upward position than the standard )
Less draft *
* Be careful of the smudge on ceiling.
PCA-KA
No vane function
Standard
Less draft *
( Upward position than the standard )
OCH567
