Mitsubishi Electric Mr. SLIM PLA-SM EA Series, Руководство по эксплуатации

Страница: 10 / 176

10
3. Operation 3. Operation
■
Manual vane angle (Wired remote controller)
F1 F2 F3 F4
Main
Main display:
Cursor Page
Main menu
Maintenance
Initial setting
Service
F1 F2 F3 F4
Maintenance menu
Main menu:
Cursor
Auto descending panel
Manual vane angle
3D i-See sensor
F1 F2 F3 F4
Manual vane angle
Input display:
Cur. Address Check
Ref. address
Unit No.
Identify unit Check button
F1 F2 F3 F4
F1 F2 F3 F4
Manual vane angle
Manual vane angle
Select:
Setting
Outlet Angle
Note:
Do not set the draft reduction in an environment with high humidity.
Otherwise, condensation may form and drip.
1
Select “Maintenance” from the
Main menu (refer to page 8), and
press the [SELECT] button.
2
Select “Manual vane angle” with
the [F1] or [F2] button, and press
the [SELECT] button.
3
Move the cursor to “Ref. address”
or “Unit No.” with the [F1] button
to select.
Select the refrigerant address
and the unit number for the units
to whose vanes are to be fi xed,
with the [F2] or [F3] button, and
press the [SELECT] button.
• Ref. address: Refrigerant ad-
dress
• Unit No.: 1, 2, 3, 4
Press the [F4] button to confi rm
the unit.
The vane of only the target
indoor unit is pointing downward.
4
The current vane setting will ap-
pear.
Select the desired outlets from
1 through 4 with the [F1] or [F2]
button.
• Outlet: “1”, “2”, “3”, “4” and “1, 2,
3, 4, (all outlets)”
Press the [F3] or [F4] button to
go through the option in the order
of “No setting (reset)”, “Step 1”,
“Step 2”, “Step 3”, “Step 4”, “Step
5” and “Draft reduction*”.
Select the desired setting.
* Draft reduction
The airfl ow direction for this set-
ting is more horizontal than the
airfl ow direction for the “Step 1”
setting in order to reduce a drafty
feeling. The draft reduction can
be set for only 1 vane.
■
Vane setting
Press the [SELECT] button to save the settings.
A screen will appear that indicates the setting information is being trans-
mitted.
The setting changes will be made to the selected outlet.
The screen will automatically return to the one shown above (step 5)
when the transmission is completed.
Make the settings for other outlets, following the same procedures.
If all outlets are selected, will be displayed the next time
the unit goes into operation.
Navigating through the screens
• To go back to the Main menu ................ [MENU] button
• To return to the previous screen .......... [RETURN] button
■
Manual vane angle (Wireless remote controller)
Fig. 1
A
Fig. 2
B
Fig. 3
Step 1 Step 2
Step 3
No setting
Draft
reduction*
All outlets
Step 5 Step 4
1
Going to the Manual vane setting
mode
Press the button.
(Start this operation from the sta-
tus of remote controller display
turned off.)
“FUNCTION” is lighted and “1”
blinks. (Fig. 1)
Press the button to select “2”,
and then press the button.
2
Selecting the vane number (Fig.
2)
Press the buttons to select
the vane number
A
, and then
press the button.
3
Setting the vane angle (Fig. 3)
Press the buttons to select
the vane angle
B
.
Point the wireless remote control-
ler toward the receiver on the
indoor unit, and then press the
button.
Display
Setting Step 1 Step 2 Step 3 Step 4
Display No display
Setting Step 5 No setting Draft reduction*
* The draft reduction can be set for only 1 vane.
The setting is enabled only for the last vane that was set.
RG79F077H03_EN.indd 10 9/1/2017 11:56:27 AM