1622
18 CC-LINK IE FIELD NETWORK INSTRUCTIONS
18.5 Reading the Module Model Information of an Intelligent Device Station
*1 A channel used only for the SINFTYRD and SINFSTRD instructions. The same channel used for the remote instructions (such as
REMFR and REMTO instructions) and the link dedicated instructions (such as the READ and SEND instructions) can be set.
Processing details
• These instructions read the model names of modules and units used in an intelligent device station, and store the data to
the device specified by (d1) and later.
• The result of instruction execution is stored in the 1st word and a model name is stored in the 2nd to 10th words of each
item. The following table lists the values to be stored in the corresponding words.
*2 If the read target module has a hardware failure, -1 may be stored in the 1st word.
+12
Clock data
(Set only in an
abnormal state)
Upper 8 bits: Month (01H to 12H)
Lower 8 bits: Year (00H to 99H: Lower two digits of the year)
System
+13
Upper 8 bits: Hour (00H to 23H)
Lower 8 bits: Day (01H to 31H)
System
+14
Upper 8 bits: Second (00H to 59H)
Lower 8 bits: Minute (00H to 59H)
System
+15
Upper 8 bits: Year (00H to 99H: Upper two digits of the year)
Lower 8 bits: Day of the week (00H (Sun.) to 06H (Sat.))
System
+16
Error detection network
number
The network number of the station in which an error was detected is stored. (No
information is stored if an error is detected in the own station.)
• 1 to 239 (Network number)
System
+17
Error-detected station
number
The number of the station where an error was detected is stored. (No information is
stored if an error is detected in the own station.)
• 125: Master station
• 1 to 120: Local station, intelligent device station, submaster station
System
Operand
Item
(d1)+0 to (d1)+9
Main base unit: power supply information 1
(d1)+10 to (d1)+19
Main base unit: power supply information 2
(d1)+20 to (d1)+29
1st extension base unit: power supply information 1
(d1)+30 to (d1)+39
1st extension base unit: power supply information 2
(d1)+140 to (d1)+149
7th extension base unit: power supply information 1
(d1)+150 to (d1)+159
7th extension base unit: power supply information 2
(d1)+160 to (d1)+169
Main base unit information
(d1)+170 to (d1)+179
1st extension base unit information
(d1)+230 to (d1)+239
7th extension base unit information
(d1)+240 to (d1)+249
CPU slot: product information
(d1)+250 to (d1)+259
I/O slot 0: product information
(d1)+260 to (d1)+269
I/O slot 1: product information
(d1)+880 to (d1)+889
I/O slot 63: product information
Condition
1st word
2nd to 10th words
The read target module or unit has a model name.
0
Model name held by a module or a unit
The read target module or unit does not have a model
name.
1
Character string consisting of module type and the
number of points
The read target slot is empty.
0000H
The read target module is being changed online.
Operand: (s)
Device
Item
Description
Setting range
Set by
Содержание MELSEC iQ-R Series
