Mitsubishi Electric MELSEC FX-1HC Скачать руководство пользователя страница 8

Страница: 8 / 12

(5) BFM #13, #12 Comparison value for YH output, BFM #15, #14 Comparison value for YS output

●

After comparing the current value of the counter with
the value written in BFM #13 and #12, BFM #15 and
#14, the hardware and software comparator in the FX-
1HC outputs the comparison result.

●

YH, YS output will not turn ON if you use PRESET or
the TO instruction to set the counter value equal to the
comparison value. It will turn ON only when a match
occurs by the counting of input pulses.

●

The YS comparison operation takes about 300

s, and

if a match occurs, the output goes ON.

●

Output occurs when the current value becomes equal
to the compare value but only if b1 and b2 of BFM #4
are ON. Once an output is set, it remains ON until it is
reset by b9 or b10 of BFM #4. If b3 of BFM #4 is ON,
however, one of the outputs is reset when the other is
set.

Current value

BFM #4

b9, b10

BFM #4

b9, b10

Coincidence output

(6) Counter current value (BFM #21, 20)
The current value of the counter can be read by the PC. It will not be the correct value during high-speed
operations because of the communication delay. The current value of the counter can be forcibly changed
by writing a 32-bit value into the appropriate BFMs from the PC.
(7) Maximum count value (BFM #23, 22)
These store the maximum and minimum value reached by the counter. If the power is turned off, the
stored data is cleared.
(8) Comparison status (BFM #26)

When ‘1’ (ON)

Set value

current value

Set value

current value

Set value

current value

BFM #26 is for reading only. Write commands from the programmable controller are ignored.
(9) Terminal status (BFM #27)

BFM #27

b4 to b15

When ‘0’ (OFF)

YH output is OFF.

YS output is OFF.

When ‘1’ (ON)

YH output is ON.

YS output is ON.

Undefined

BFM #26

When ‘0’ (OFF)

Set value

≤

current value

Set value

≠

current value

Set value

≥

current value

When ‘1’ (ON)

Set value

current value

Set value

current value

Set value

current value

BFM #26

When ‘0’ (OFF)

Set value

≤

current value

Set value

≠

current value

Set value

≥

current value

BFM #27

When ‘0’ (OFF)

PRESET input is OFF.

DISABLE input is OFF.

When ‘1’ (ON)

PRESET input is ON.

DISABLE input is ON.

Содержание MELSEC FX-1HC













Результаты поиска

Содержание MELSEC FX-1HC

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric MELSEC FX-1HC, Руководство пользователя

Результаты поиска

Содержание MELSEC FX-1HC

Отзывы:

Бренды по названию

Популярные бренды