Mitsubishi Electric MELPRO CBV2 -A02S1 Скачать руководство пользователя страница 10

Страница: 10 / 48

10 / 47

JEP0-IL9537

2. Relay Specification

In this section, the relay specification such as the rating and relay element is explained.

2.1. General specification (CBV2-A02S1)

Table 2-1 General specification (CBV2-A02S1)

Name

Over/Undervoltage Relay

Relay Model

CBV2-A02S1

Style

563PQB

Elements

Protection

Undervoltage element (27)

Overvoltage (59)

Rating

Frequency

50Hz / 60Hz (selectable)

Voltage

AC110V

Aux. power
supply

Voltage

AC100V

– 110 V

DC100V

– 125 V *1

Operative range

AC: 85

–126.5 V

DC: 85-143 V *1

Setting

Undervoltage
element

Operation value LOCK

– 60~120 V (1 V step) *2

Operation time

INST - 0.1~ 5.0 s (0.1 s step)

TEST MODE

OFF

– AB – BC – CA

Overvoltage
element

Operation value LOCK

– 120~165 V (1 V step) *2

Operation time

INST - 0.1~ 5.0 s (0.1 s step)

Forced
operation

Trip and control (annunciator) contacts can be forced to operate.

Operation
indication

Operation indicator LED comes on when the relay element operates.
LED indication: Undervoltage element, Overvoltage element, AB-Phase, BC-Phase, CA-Phase

Display

RUN LED (green)

Indicate the result of automatic self-diagnosis. This LED is turned
on for normal and turned off for abnormal.

ALARM LED (red)

Indicate the result of automatic self-diagnosis. This LED is turned
off for normal and turned on for abnormal.

Self-diagnosis
(ALARM)

An electronic circuit and a built-in power supply are always supervised, and it outputs to the
RUN/ALARM LED and an ALARM contact.

Burden

Phase Circuit

0.5 VA or less (with rated current)

Auxiliary supply

For 110 VDC: approx. 1.6W
For 110 VAC: approx. 1.9VA

Output Contact Configuration For trip

Normally open contact

For control

Normally open contact (for 27 and 59)

For alarm

Normally close contact

Capacity

For trip

Make:

110 VDC, 15 A, 0.5 s (L/R=0 s)

220 VDC, 10 A, 0.5 s (L/R=0 s)

Brake:

110 VDC, 0.3 A (L/R

≦

40 ms)

220 VDC, 0.15 A (L/R

≦

40 ms)

Continuation: 1.5 A

For control and
alarm

Make:

10 VA (cos



= 0.4)

10 W (L/R = 0.007 s)

Case/Cover

Color: N1.5

Mass

approx. 1.2 kg

*1: When DC125 V is used, please note that the maximum voltage of operation range is still 143V.

(A maximum is not 125 V x 30 %.)

*2: If it sets to LOCK, the protection element will be in a lock state of operation.

Содержание MELPRO CBV2 -A02S1

















































Результаты поиска

Содержание MELPRO CBV2 -A02S1

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric MELPRO CBV2 -A02S1, Руководство по эксплуатации

Результаты поиска

Содержание MELPRO CBV2 -A02S1

Отзывы:

Бренды по названию

Популярные бренды