Mitsubishi Electric LU2-4410-B1T-CS Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 28

background image

L

Installation position of the

thread trimmer cam

( 1 ) Adjust so that the gap between the feed cam

and the bushing is 17.3mm and then tighten
the screw Ⓐ to the flat on the lower shaft.

( 2 ) Place the thread trimmer cam on the end

face of the bushing and the thread tension
releasing cam on the end face of the thread
trimmer cam (making the gap between each
part zero), then tighten each screw.

M

Adjustment of the thread trimmer cam

( 1 )  Turn the pulley and stop it at the position where the needle comes to the lowest.
( 2 )  Put the cam roller into the thread trimmer cam groove by pushing the cam follower crank.
( 3 )  Turning the pulley, adjust the thread trimmer cam so that the movable knife starts moving when

the green mark point on the pulley comes in line with the black mark point on the arm.

To adjust, loosen two thread trimmer cam clamp screws Ⓐ.

HOW TO USE

Black mark point

Arm

Green mark point

Pulley

Screw Ⓐ

17.3mm

Reverse block

Bushing

Thread tension releasing cam

Thread trimmer cam

Feed cam

Feed connecting rod

Screw Ⓐ

Cam roller

Cam follower crank

Thread trimmer cam

Cam groove

— 16 —

«
...
17
18
19
20
21
...
»

Содержание LU2-4410-B1T-CS





























Отзывы:

Нет отзывов

Похожие инструкции для LU2-4410-B1T-CS

Бренд: Singer Страницы: 23

Бренд: Singer Страницы: 74

Бренд: Janome Страницы: 38

CoverPro 1000CP

Бренд: Janome Страницы: 21

Бренд: Encore Страницы: 28

Бренд: National Страницы: 27

Бренд: IPC Soteco Страницы: 40

Бренд: Tennant Страницы: 6

LAVINA ELITE Series

Бренд: Superabrasive Страницы: 48

Бренд: Radio Shack Страницы: 24

Бренд: Janome Страницы: 86

Бренд: Nilfisk-Advance Страницы: 54

Бренд: Philips Страницы: 2

MAGIC 5 ECO PPF 631

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 24

Бренд: Philips Страницы: 100

Бренд: Panasonic Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды