Mitsubishi Electric ECODAN EHPX Series Скачать руководство пользователя страница 19

Страница: 19 / 64

4.2.1

Installation

How to access Internal Components and Control
and Electrical Box

<A> Opening the front panel

1. Remove the two lower screws.

2. Slide front panel upwards slightly and open carefully.

3. Disconnect the relay connector connecting main controller cable and the control

board cable.

<B> Opening the control and electrical box cover

1. Remove the 4 screws.

2. Slide the control and electrical box cover upwards slightly and remove facing

panel.

<C>

Accessing the back of the control and electrical box

The control and electrical box has a holding screw on the right and is hinged on

the left hand side.

1. Remove the holding screw on the control and electrical box.

2. The control and electrical box can then be swung forward on the left hand

hinges.

Note:

1. Before accessing back of control and electrical box release cables from the

tie straps attached to the cross-support.

2. After servicing, re-secure all cables using straps provided. Reconnect

main controller cable to its relay connector. Replace front panel and re-

secure screws at base.

Screws

<A>

<B>

<C>

Screws

Hinges

Open

4.2 Water Quality and System Preparation

General

• Water quality should be to European Directive 98/83 EC standards.

► pH value of 6.5-8.0 (Recommended: pH6.5 - 7.5)

► Calcium ≤ 100 mg/l

► Chlorine ≤ 100 mg/l

► Iron/Manganese ≤ 0.5 mg/l

• In known hard water areas, to prevent/minimise scaling, it is beneficial to restrict

the routine stored water temperature (DHW max. temp.) to 55°C.

Anti-Freeze

Anti-freeze solutions MUST use propylene glycol with a toxicity rating of Class as

listed in Clinical Toxicology of Commercial Products, 5th Edition.

Note:

Ethylene glycol is toxic and must NOT be used in the primary water

circuit in case of any cross-contamination of the potable circuit.

New Installation (primary water circuit)

• Before connecting outdoor unit, thoroughly cleanse pipework of building debris,

solder etc using a suitable chemical cleansing agent.

• Flush the system to remove chemical cleanser.

• For all packaged model systems add a combined inhibitor and anti-freeze

solution to prevent damage to the pipework and system components.

• For split model systems the responsible installer should decide if anti-freeze

solution is necessary for each site’s conditions. Corrosion inhibitor however

should always be used.

Existing Installation (primary water circuit)

• Before connecting outdoor unit the existing heating circuit MUST be chemically

cleansed to remove existing debris from the heating circuit.

• Flush the system to remove chemical cleanser.

• For all packaged model systems add a combined inhibitor and anti-freeze

solution to prevent damage to the pipework and system components.

• For split model systems the responsible installer should decide if anti-freeze

solution is necessary for each site’s conditions. Corrosion inhibitor however

should always be used.

When using chemical cleansers and inhibitors always follow manufacturer’s

instructions and ensure the product is appropriate for the materials used in

the water circuit

Minimum amount of water required in the space

heating/cooling circuit

Outdoor heat pump unit

Minimum water quantity [L]

Packaged model

PUHZ-W50

PUHZ-W85

PUHZ-HW2

PUHZ-HW140

100

Split model

PUHZ-RP35

PUHZ-RP50

PUHZ-RP60

PUHZ-(H)RP71

PUHZ-(H)RP100

PUHZ-(H)RP125

100

PUHZ-RP140

120

PUHZ-SW40

PUHZ-SW50

PUHZ-SW75

PUHZ-SW100

PUHZ-SW120

120

PUHZ-SHW80

PUHZ-SHW2

PUHZ-SHW140

100

Screw

Содержание ECODAN EHPX Series

































































Результаты поиска

Содержание ECODAN EHPX Series

Отзывы:

Похожие инструкции для ECODAN EHPX Series

Бренды по названию

Популярные бренды

Mitsubishi Electric ECODAN EHPX Series, Руководство по установке

Результаты поиска

Содержание ECODAN EHPX Series

Отзывы:

Похожие инструкции для ECODAN EHPX Series

Бренды по названию

Популярные бренды