Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 162

background image

66

7 FUNCTIONS
7.1 IO-Link Master Functions

IO-Link device setting automatic upload/download function

This function saves the parameter setting of the IO-Link device connected to each channel in the IO-Link module, and as
necessary, overwrites the parameter setting of the IO-Link devices.
Use this function to inherit parameter setting of an IO-Link device when replacing it.
The CQ LED flashes in green during uploading or downloading.
On the parameter setting window of the engineering tool or via a program, enable/disable automatic download of IO-Link
device parameters and automatic upload of directly modified IO-Link device parameters for each channel.
For details on setting parameters via a program, refer to the following.



Page 88 Data storage configuration

Description

The following table lists the IO-Link device conditions, and relevant settings and operations.

*1 No processing is performed if the parameter setting data in the connected IO-Link device is not compatible with the parameter setting

data in the IO-Link module.

*2 When the IO-Link module has no parameter setting data, parameter setting data will be uploaded even when the upload setting is

disabled.

*3 Depending on the IO-Link device setting, the upload operation may take precedence even when the download setting is enabled. (



Page 68 Precautions)

Setting procedure

1.

Open the "CC IE Field Configuration" window.

For the master/local module RJ71GF11-T2

[Navigation window]



[Parameter]



[Module Information]



[RJ71GF11-T2]



[Module Parameter]



[Basic Settings]



[Network Configuration Settings]

2.

Open the "Parameter Processing of Slave Station" window.

From the list of stations, select an IO-Link module



[CC IE Field Configuration]



[Online]



[Parameter Processing of

Slave Station].

3.

Set "Method selection" to "Parameter Write".

IO-Link module condition

Setting details

Operation after executing the
function

Download setting

Upload setting

No parameter setting data

Disabled

Disabled

No processing

Enabled

Upload

Enabled

Disabled

Upload

Enabled

Upload

With parameter setting data

Disabled

Disabled

No processing

Enabled

Upload

Enabled

Disabled

Download

Enabled

Download

«
...
66
67
68
69
70
...
»

Содержание CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CC-Link IE Field NZ2GF12A-60IOLH8

Бренд: Jafar Страницы: 9

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 32

Бренд: Danfoss Страницы: 32

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 44

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 144

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 64

Бренд: Danfoss Страницы: 8

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 6

Бренд: Danfoss Страницы: 4

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 2

ECL Comfort 110

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 24

Бренд: K&K Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды