Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 Скачать руководство пользователя страница 29

Страница: 29 / 162

3 PROCEDURES BEFORE OPERATION

PROCEDURES BEFORE OPERATION

This chapter describes the procedures before operation.

Installation

Mount the IO-Link module. (



Page 33 INSTALLATION AND WIRING)

Wiring

Wire a power supply, an Ethernet cable, and an external device to the IO-Link module. (



Page 33 INSTALLATION AND

WIRING)

Station number setting

Power on the IO-Link module and set the station number. (



Page 18 Network configuration)

CC-Link IE Field Network parameter setting

Connect an engineering tool to the CC-Link IE Field Network master station and configure the CC-Link IE Field Network
parameters. (



Page 45 CC-Link IE Field Network Parameter Setting)

IO-Link module parameter setting

Use an engineering tool to configure the IO-Link module parameters. (



Page 47 IO-Link Module Parameter Setting)

Programming

Create a program. (



Page 99 PROGRAMMING)

To replace the IO-Link module, follow the procedure described below.
• Turn off the IO-Link module power supply and remove the IO-Link module.
• Prepare a new IO-Link module and perform the above procedure for wiring, parameter setting, and

programming. (The network parameters of the CC-Link IE Field Network master station do not need to be
set again.)

• After checking the operation, restart the control.

Содержание CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Результаты поиска

Содержание CC-Link IE Field NZ2GF12A-60IOLH8

Отзывы:

Похожие инструкции для CC-Link IE Field NZ2GF12A-60IOLH8

Бренды по названию

Популярные бренды

Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8, Руководство пользователя

Результаты поиска

Содержание CC-Link IE Field NZ2GF12A-60IOLH8

Отзывы:

Похожие инструкции для CC-Link IE Field NZ2GF12A-60IOLH8

Бренды по названию

Популярные бренды