Mitsubishi Electric A800-E Скачать руководство пользователя страница 80

Страница: 80 / 84

Common specifications

SPECIFICATIONS



Available only for the standard model.



This protective function is not available in the initial status.



Temperature applicable for a short time, e.g. in transit.



For the installation at an altitude above 1000 m (up to 2500 m), consider a 3% reduction in the rated current per altitude increase of 500 m.



2.9 m/s

or less for the FR-F840-04320(185K) or higher.

nmen

Surrounding air
temperature

-10°C to +50°C (non-freezing) (LD rating)
-10°C to +40°C (non-freezing) (SLD rating)

Surrounding air humidity

With circuit board coating (conforming to IEC60721-3-3 3C2/3S2): 95% RH or less (non-condensing)
Without circuit board coating: 90% RH or less (non-condensing)

Storage temperature



-20°C to +65°C

Atmosphere

Indoors (without corrosive gas, flammable gas, oil mist, dust and dirt, etc.)

Altitude/vibration

1000 m or lower



, 5.9 m/s

or less



at 10 to 55 Hz (directions of X, Y, Z axes)

Содержание A800-E





















































































Результаты поиска

Содержание A800-E

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric A800-E, Инструкция по эксплуатации

Результаты поиска

Содержание A800-E

Отзывы:

Бренды по названию

Популярные бренды