Mitsubishi Electric 2.5KKC Скачать руководство пользователя страница 29

Страница: 29 / 36

8. Test run

8.3. Self-diagnosis

For available LED displays (LEDs 1, 2) on the indoor unit board,
refer to the table below.

The temperature code is indicated by numbers 1 through 15 which
represent -40

to 90

Check the compressor operation by confirming that the code
number decreases when cooling and increases when heating.

Code

Indoor coil temperature -40

C ~ 1

C 2

C ~ 10

C ~ 15

C 16

C ~ 20

Code

Indoor coil temperature 21

C ~ 25

C 26

C ~ 30

C 31

C ~ 35

C 36

C ~ 40

Code

Indoor coil temperature 41

C~ 45

C 46

C ~ 50

C 51

C ~ 55

C 56

C ~ 60

Code

Indoor coil temperature 61

C~ 70

C 71

C ~ 90

Sensor malfunction

LED2 (Microprocessor
power supply)

LED1 (Remote control-
ler power supply)

Should remain ON always to indicate the con-
trol power supply is turned ON.
Lights up to indicate the power is connected
to the wired remote controller.

Lights up only for the indoor unit connected to
the outdoor unit address “0”.

8.4. Check of Drainage

•

At the of trial run, ensure the water is being properly drained out and
that no water is leaking from joints.

•

Always make this check at the time of installation during other air-
conditioning (cooling) season.

•

Similarly, check it also before finishing the ceiling of new premises.

(1) Remove the cover of water supply inlet, and fill in about 1000 cc of

water, using water supply pump, etc. While filling water, ensure that it
is not sprayed into the internal drain lift up mechanism.

(2) Confirm that water is being drained out through the drainage outlet,

after switching over from remote control mode to trial run mode.

(3) After checking, fit back the cover without fail, and cut off the main power

supply switch.

(4) When installing during other than air-conditioning out the water. After

confirming that water drains out, fit back the drain plug.

Insert the pump end 3 to 5 cm

Cover of water supply inlet (to remove off its screw & pull it downward)

About 1000 cc

Water

Drain plug

Содержание 2.5KKC





































Результаты поиска

Содержание 2.5KKC

Отзывы:

Похожие инструкции для 2.5KKC

Бренды по названию

Популярные бренды

Mitsubishi Electric 2.5KKC, Руководство по установке

Результаты поиска

Содержание 2.5KKC

Отзывы:

Похожие инструкции для 2.5KKC

Бренды по названию

Популярные бренды