background image

 

SAFETY PRECAUTIONS 

INTRODUCTION 

 

 

Read this Owner/Operator Manual carefully. Be sure you understand how to operate this brush cutter 
properly before you use it. Failure to do so could result in serious injury.   

 

Keep this manual handy so that you may refer to it later whenever any 
questions arise. Also note that you are able to contact the dealer from 
whom you purchased the product for assistance. 

 

Always include this manual when selling, lending, or otherwise 
transferring the ownership of this product.   

 

This product has been designed to be used as a brush cutter/grass 
trimmer for cutting fresh growth and it should never be used for any other 
purpose, doing so could result in unforeseen accidents and injuries 
occurring. 

 

This brush cutter is equipped with extremely sharp blades, always wear sturdy 
gloves when handling the blades. 

 

When using this brush cutter for the first time, take the brush cutter to a wide, 
clear, open space, start the engine, and practice handling the brush cutter until 
you are sure that you will be able to handle it properly in actual operation. 

 

You should never use this brush cutter when under the influence of alcohol, 
suffering from exhaustion or lack of sleep, suffering from drowsiness as a result 
of having taken medicine, or at any other time when your judgement might be 
impaired or that you might not be able to operate the brush cutter properly and in 
a safe manner.   

 

Never allow children or anyone unable to fully understand the directions given in this manual to use this 
brush cutter.   

 

When planning your work schedule, allow plenty of time to perform the work and allow plenty of time for 
rest.    Limit the amount of time you continuously use the brush cutter to 30~40 minutes per session and 
take 10~20 minutes of rest between work sessions.    Also, try to keep the total amount of work 
performed in a single day to 2 hours. 

 

Never run the engine indoors as the exhaust gases contain harmful carbon monoxide. 

 

Never use the brush cutter in conditions as described below:   

 

 

When the ground is slippery or when other conditions exist which might make it difficult to maintain a 
steady posture while using the brush cutter. 

 

At night, at times of heavy fog, or at any other times when your field of vision is limited and it would be 
difficult to gain a clear view of the area where the brush cutter is to be used. 

 

In heavy rain, during lightning storms, at times of strong or gale-force winds, or at any other times when 
weather conditions might make it unsafe to use this product. 

 

Lack of sleep, tiredness, or physical exhaustion results in lower attention spans, and this in turn can lead 

to accidents and injury.   

 

 

WORK CLOTHING AND SAFETY EQUIPMENT 
 
When using the product, you should wear proper clothing and protective equipment.

 

 

  

Helmet  

 

  Protection goggles or face protector 

  

Ear 

protectors 

  

Thick 

work 

gloves 

 

  Non-slip sole work boots 

 

  When using your brush cutter, always wear strong, durable,     
  work clothing; shirts should be long-sleeved and trousers           
  should be full-length. 

 
 
 
 

 

Содержание 2800




























Отзывы: