3
Thread the supplied LAN/Ethernet cable plug through the slot on the back
of the UC360 unit and plug it into the Ethernet port on the back of the UC360.
Plug the other end of the LAN cable into one of the following:
• the phone port of an Ethernet power adapter. Then, connect the
Ethernet adapter to the LAN using a separate LAN cable, and plug the
power adapter into an AC power outlet.
or
• a 802.3at LAN-powered jack.
Insert a USB adapter for a wireless keyboard and mouse.
Thread the supplied-HDMI cable throught the slot on the back of the UC360
unit and plug it into the HDMI port
Connect the other end into the HDMI device or another HDMI cable.
Used for audio input with an extension microphone base station.
Configuration Requirements
The UC360 Collaboration Point must be licensed, programmed, and registered
with the communications platform. Refer to your communications platform
documentation for instructions.
NOTE: Communication platform documentation and associated UC360
Collaboration Point documentation are available on the Mitel Customer
Documentation web site. See “Supporting Documentation” on page 2 for more
information.
Notice to Canadian Customers
Contains IC: 5969A-TIWI1-01
The term "IC:" before the certification/registration number only signifies that
registration was performed based on a Declaration of Conformity indicating that
Industry Canada technical specifications were met. It does not imply that
industry Canada approved the equipment.
This device complies with Industry Canada License-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Notice to U.S. Customers
Contains FCC ID: TFB-TIWI1-01.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING
TEST CALLS TO EMERGENCY NUMBERS
• Remain on the line and briefly explain to the dispatcher the reason for the
call.
• Perform tests during off-peak hours such as early morning or late
evenings.
RF Exposure
This device complies with FCC/ and Industry Canada RF exposure limits for
general population / uncontrolled exposure.
WARNING: To ensure compliance with FCC and Industry Canada RF
exposure requirements, the UC360 must be installed such that a
minimum separation distance of 20cm is maintained between the
radiator (antenna) and all persons at all times. The UC360 and
must not be co-located or operating in conjunction with any other
antenna or transmitter.
Notice to Customers in EU Countries
We, Mitel Networks Ltd.
Of, Castlegate Business Park
Portskewett
Monmouthshire
NP26 5YR
UK
Declare that for the hereinafter mentioned product the presumption of
conformity with the applicable essential requirements of
DIRECTIVE 1995/5/EC OF THE EUROPEAN
PARLIAMENT (RTTE DIRECTIVE) AND OF THE COUNCIL
is given.
Mitel Networks / UC360
Any unauthorized modification of the product voids this Declaration.
For a copy of the original signed Declaration of Conformity (in full conformance
with EN45014), please contact the Regulatory Approvals Manager at the above
address.
