95
80
80
50QMA
50QMA
N/B Maintenance
N/B Maintenance
5.2 Intel ICH6-M South Bridge(8)
General Purpose I/O Signals 1,2
Name Type
Tolerance
Power
Well
Description
GPO[49]
OD O V_CPU_IO
`Core
This signal is fixed as output only and can
instead be used as CPUPWRGD.
GPO[48]
O
3.3 V
Core
This signal is fixed as output only and can
instead be used as GNT4#.
GPIO[47:42]
N/A
N/A
N/A
This signal is not implemented.
GPI[41]
I
3.3 V
Core
This signal is fixed as input only and can be used
instead as LDRQ1#.
GPI[40]
I
5 V
Core
This signal is fixed as input only and can be used
instead as REQ4#.
GPIO[39:35]
N/A
N/A
N/A
This signal is not implemented.
GPIO[34:33]
I/O
3.3 V
Core
This signal can be input or output and is
unmultiplexed
GPIO[32]
I/O
3.3 V
Core
This signal can be input or output.
GPI[31]
I
3.3 V
Core
This signal is fixed as input only and can instead
be used for SATA[3]GP.
GPI[30]
I
3.3 V
Core
This signal is fixed as input only and can instead
be used for SATA[2]GP.
GPI[29]
I
3.3 V
Core
This signal is fixed as input only and can instead
be used for SATA[1]GP.
GPIO[28:27]
I/O
3.3 V
Resume
This signal can be input or output and is
unmultiplexed.
GPI[26]
I
3.3 V
Core
This signal is fixed as input only and can instead
be used for SATA[0]GP.
GPIO[25]
I/O
3.3 V
Resume
This signal can be input or output and is
unmultiplexed. It is a strap for internal Vcc2_5
regulator. See Section 2.22.1.
GPIO[24]
I/O
3.3 V
Resume
This signal can be input or output and is
unmultiplexed.
GPO[23]
O
3.3 V
Core
This signal is fixed as output only.
GPIO[22]
N/A
N/A
N/A
This signal is not Implemented
GPO[21]
O
3.3 V
Core
This signal is fixed as output only and is
unmultiplexed
GPO[20]
O
3.3 V
Core
This signal is fixed as output only.
GPO[19]
O
3.3 V
Core
This signal is fixed as output only.
NOTE:
GPO[19] may be programmed to blink
(controllable by GPO_BLINK (D31:F0:Offset
G18h:bit 19)).
General Purpose I/O Signals 1,2 (Continued)
Name Type
Tolerance
Power
Well Description
GPO[18]
O
3.3 V
Core
This signal is fixed as output only.
NOTE:
GPO[18] will blink by default
immediately after reset (controllable by
GPO_BLINK (D31:F0:Offset
G18h:bit 18)).
GPO[17]
O
3.3 V
Core
This signal is fixed as output only and can be
used instead as PCI GNT[5]#.
GPO[16]
O
3.3 V
Core
This signal is fixed as output only and can be
used instead as PCI GNT[6]#.
GPI[15:14]3
I
3.3 V
Resume
This signal is fixed as input only and can be used
instead as OC[7:6]#
GPI[13]3
I
3.3 V
Resume
This signal is fixed as input only and is
unmultiplexed.
GPI[12]3
I
3.3 V
Core
This signal is fixed as input only and is
unmultiplexed.
GPI[11]3
I
3.3 V
Resume
This signal is fixed as input only and can be used
instead as SMBALERT#.
GPI[10:9]3
I
3.3 V
Resume
This signal is fixed as input only and can be used
instead as OC[5:4]#.
GPI[8]3
I
3.3 V
Resume
This signal is fixed as input only and is
unmultiplexed.
GPI[7]3
I
3.3 V
Core
This signal is fixed as input only and is
unmultiplexed.
GPI[6]3
I
3.3 V
Core
This signal is fixed as input only.
GPI[5:2]3
I
5 V
Core
This signal is fixed as input only and can be used
instead as PIRQ[H:E]#.
GPI[1:0]3
I
5 V
Core
This signal is fixed as input only and can be used
instead as PCI REQ[6:5]#.
NOTES:
1.All inputs are sticky. The status bit remains set as long as the input was asserted for two
clocks.GPIs are sampled on PCI clocks in S0/S1. GPIs are sampled on RTC clocks in S3/S4/S5.
2.Some GPIOs exist in the VccSus3_3 power plane. Care must be taken to make sure GPIO
signals are not driven high into powered-down planes. Some ICH6 GPIOs may be connected to
pins on devices that exist in the core well. If these GPIOs are outputs, there is a danger that a
loss of core power (PWROK low) or a Power Button Override event will result in the Intel
ICH6 driving a pin to a logic 1 to another device that is powered down.
3.GPI[15:0] can be configured to cause a SMI# or SCI. Note that a GPI can be routed to either
an SMI# or an SCI, but not both.
MiTac Secret
Confidential Document
