12
Mirka® DEOS 353X, 383X & Delta 663X • 110 V
Mirka® DEOS 353X, 383X & Delta 663X • 110 V
13
en
* The values stated in the table are derived from laboratory testing in conformity with stated codes and standards and
are not sufficient for risk evaluation . Values measured in a particular work place may be higher than the declared
values . The actual exposure values and amount of risk or harm experienced by an individual are unique to each
situation and depend upon the surrounding environment, the way in which the individual works, the particular
material being worked, work station design and the user's exposure time and physical condition . Mirka Ltd accepts
no responsibility for the consequences of using declared values instead of actual exposure values for any individual
risk assessment .
Proper use of tool
This sander is designed for sanding all types of materials, i .e . metals, wood, stone, plastics, etc . using abrasives
designed for this purpose . Do not use this sander for any other purpose than that specified without consulting the
manufacturer or the manufacturer’s authorized supplier . Only use original Mirka backing pads that are designed for
optimal performance . Other backing pads may reduce performance and will increase vibration . The cooling air vents
on the housing must be kept clean and free of blockages to ensure air circulation . Any maintenance or repair work may
only be carried out by an authorized service center .
Work stations
The tool is intended to be operated as a hand-held tool . It is always recommended that the tool should be used when
standing on a solid floor . It can be used in any position but before any such use, the operator must be in a secure
position have a firm grip and footing, and be aware that the sander can develop a torque reaction . See the section
“Operating instructions” .
How to get started
When unpacking the tool, make sure it is intact, complete and has not been damaged in transport . Never use a
damaged tool .
Before use, check that the backing pad is correctly mounted and tightened . Connect the power cord to the sander .
Connect the power cord to a grounded outlet (100–120 VAC, 50/60 Hz) .
In order to get the maximum power from this tool it is recommended to use it with the Mirka dust extractor and
Mirka Net Sanding products . The combination of Mirka sanders, net sanding products and Mirka dust extractor are the
basis of Mirka dust-free sanding solutions .
The power cord from the sander is connected to the mains supply on the front of the dust extractor . By connecting the
sander’s power cord to the outlet on the dust extractor it is possible to use the dust extractor’s autostart function .
Operating instructions
• The tool is intended to be operated as a hand-held tool . The tool can be used in any position . Note! The sander can
develop a torque reaction when started .
• Make sure the sander is switched off . Select a suitable abrasive and secure it to the backing pad . Make sure the
abrasive is centered on the backing pad . For optimal performance we recommend that this tool is used with other
Mirka products and accessories .
• Switch on the sander by pressing the On/Off key, Figure 1 . The sander LED (right) is now green .
• The sander can now be started by pressing the lever .
• The speed can be adjusted between 5,000 and max rpm by adjusting the position of the lever .
• The max rpm can be adjusted by pressing rpm+ or rpm–, Figure 1 . The rpm can be adjusted in steps 5,000, 6,000,
7,000, 7,500, 8,000, 9,000 and 10,000 rpm .
• The tool has two speed control modes . In the default mode the speed can be adjusted linearly by changing the
position of the lever . In the other mode the speed remains fixed at the set max rpm when the tool is running . When
the rpm+ and rpm– buttons are pressed simultaneously the tool toggles between the two controlling modes .
• When sanding, always place the tool on the work surface before starting the tool . Always remove the tool from the
work surface before stopping it .
• When sanding is finished, turn off the sander by pressing the On/Off key . The sander LED (right) is now turned off .
Содержание DEOS 353
Страница 1: ...Mirka DEOS 353X 383X Delta 663X...
Страница 2: ......
