Miranda NV5256 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 56

background image

36

Rev 1.7 • 18 Aug 10

5. Maintenance

Intake Air Filter Cleaning

1 Ensure that there are no missing backplane cover plates. Cover plates (used where there are no

backplanes installed) are required for proper cooling in the frame.

2 Place your hand near the air exhausts (at the top). You should feel strong, evenly distributed air

pressure across the entire opening.

3 Check cable connectors for any sign of unseating.

4 Verify that one or both AC cords are firmly seated at both ends. Make sure that the power cord

retainers on the rear of the frame are in place.

Intake Air Filter Cleaning

The air intake filter is located on the front door assembly of the NV5256. Slide the filter up and to
the right to remove it. The process might be easier if you remove the entire door. To remove the
door, simply open the door and lift it straight up. The router can be operated safely with the door
removed for short periods of time.

If the filter is only lightly contaminated with debris, remove loose debris and dirt with a vacuum
cleaner or by blowing air from the clean side to the dirty side. For filters that are badly clogged, a
rinse with cold water might prove effective. You can wash the filter with warm water and mild
detergent. Make sure the filter is completely dry before re-installing it.

Battery Replacement

A CR2330 lithium coin cell is located on the front edge of the router control card. This battery pro-
vides power to maintain the memory contents when power is lost.

If the router control card is continuously powered, the battery should last for several years or more.
If the router control card is frequently powered down, the battery should be replaced every 6
months. A red LED, located directly above the battery holder, illuminates when the battery is low.

The battery can be replaced while the router control card is powered up and operating. Simply pull
the battery from its holder to remove the spent cell. Insert the replacement in the holder while care-
fully observing the polarity of the battery.

Note

Be sure to replace and close the door when you are done. The door ensures that
air entering the frame is properly filtered.

«
...
42
43
44
45
46
...
»

Содержание NV5256

























































Отзывы:

Нет отзывов

Похожие инструкции для NV5256

Бренд: Campbell Hausfeld Страницы: 12

SilverStorm 9000

Бренд: Qlogic Страницы: 50

Бренд: IDEM SAFETY SWITCHES Страницы: 2

Бренд: F&G Страницы: 6

Бренд: Dahua Страницы: 15

SIL IntelliPoint RF S*R*L Series

Бренд: Ametek Страницы: 93

Бренд: Orno Страницы: 2

Бренд: Black Box Страницы: 2

Бренд: Advantech Страницы: 101

Бренд: WTI Страницы: 56

Бренд: Cabletron Systems Страницы: 105

Area box distribution switch

Бренд: LEGRAND Страницы: 87

Бренд: ALFAtron Страницы: 23

8 Port 10/100 Ethernet Switch

Бренд: OnQ Technologies Страницы: 14

Бренд: Epcom Страницы: 2

Бренд: Blue Sea Systems Страницы: 2

EZ HUB 10/100 5608DS

Бренд: SMC Networks Страницы: 2

Бренд: Altusen Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды