Mirage IAEH121A Скачать руководство пользователя страница 35

Страница: 35 / 44

Installation of outdoor unit

Step one: fix the support of outdoor unit (select it according to the

actual installation situation)

1. Select installation

ocation according to the house structure.

2. Fix the support of outdoor unit on the selected location with expansion

screws.

Note:

• Take sufficient protective measures

when installing the outdoor unit.

• Make sure the support can with

stand at least four times of the unit

weight.

• The outdoor unit should be installed

at least 2’’ above the floor in order to

install drain joint.

• For the unit with cooling capacity

of 2300W ~5000W, 6 expansion

screws are needed; for the unit with

cooling capacity of 6000W ~8000W, 8

expansion screws are needed; for the

unit with cooling capacity of 10000W

~16000W, 10 expansion screws are

needed

Step two: install drain joint (Only

for cooling and heating unit)

1. Connect the outdoor drain joint

into the hole on the chassis, as

shown in the picture below.

2. Connect the drain hose into the

drain vent.

Step three: fix outdoor unit

1. Place the outdoor unit on the

support.

2. Fix the foot holes of outdoor unit

with bolts.

at least 2’’ above the floor

Содержание IAEH121A













































Результаты поиска

Содержание IAEH121A

Отзывы:

Похожие инструкции для IAEH121A

Бренды по названию

Популярные бренды

Mirage IAEH121A, Руководство пользователя

Результаты поиска

Содержание IAEH121A

Отзывы:

Похожие инструкции для IAEH121A

Бренды по названию

Популярные бренды