background image

Mirage B-

320

-G Instruction Manual 

-

9-

 

MIRAGE 

COMMUNICATION EQUIPMENT 

 

300 Industrial Park Road 

Starkville, MS 39759  USA 

Tel: (601) 323-8287 

FAX: (601) 323-6551 

 

ONE YEAR LIMITED WARRANTY 

 

Any Mirage Communications product found to be defective in materials or workmanship will be 
repaired or replaced (at Mirage’s option) for a period of one year from the date of original purchase. 
 
During the warranty period Mirage Communications will provide, free of charge, both parts and 
labor necessary to correct defects in material or workmanship. 
 
To obtain such warranty service, the original purchaser must: 
 
 

(1) Provide “proof of purchase” 

 
 

(2) Ship the product in its original container or equivalent, fully insured and shipping  

 

 

      charges prepaid, to Mirage, as addressed below. 

 
All internal adjustments are factory set for best performance consistent with reliable operation.  
Changing internal adjustments may void this warranty. 
 
Improper maintenance or repair may also void this one year warranty.  We recommend that units 
requiring repair during the warranty period be returned to the factory. 
 
This unit was not designed for repeater operation, and its use in such service is at your own risk. 
 
Mirage assumes no responsibility for any item connected to or used in conjunction with this product. 
 
The foregoing constitutes Mirage’s entire obligation with respect to this product and the original 
purchaser and any user or owner shall have no remedy and no claim for incidental or consequential 
damages. 
 
All Mirage products to be serviced, in-warranty or out-of-warranty, should be shipped, freight paid 
to: 

Mirage, 921 Louisville Road, Starkville, MS 39759, USA

.  Product must be accompanied by a 

letter describing the problem in detail.  Be sure to include 

YOUR NAME, ADDRESS, AND 

TELEPHONE NUMBER!

 

 
This warranty gives specific legal rights and you may also have other rights which vary from state to 
state. 
 

WARNING

: This unit should not be operated with the cover removed.  The cover confines RF 

radiation.  The harmonic filters contained in the circuit will not suppress direct radiation that may 
result if the cover is removed. 

Содержание B-320-G











Отзывы: