5
6
• Install trip lever. Follow instructions packed
with the trip lever.
• Connect supply shut-off valve to toilet
supply shank.
• Open supply shut-off valve slowly to check
for leaks. If the connections have been
properly assembled, a slight tightening of
the nuts should stop any leakage.
• Install toilet seat according to the packed
instructions.
• Adjust tank water level to the proper
marked waterline by rotating threaded rod
clockwise to raise water level or
counterclockwise to lower water level.
• Carefully set cover onto tank.
Tubing
Ferrule
Supply shank
Tank
Seal washer
Tubing
Ferrule
Fill valve nut
Supply shut-off
valve
Compression
nut
Compression
nut
Coupling
nut
Comp.
washer
Coupling
nut
Waterline
Filter
screen
Remove tape before
flushing.
Adjust water
level
Washer
Waterline
Filter
screen
Cap
Trip
lever
Fill valve
Locknut
Nut
Hose
Flapper
Seal
Flush
valve
Nut
Clip
5. CONFIRM OPERATION
• Flush toilet several times and check all
connections for leaks.
• Periodically check for leaks for several days
following the installation.
Attention Installer:
Recommended water pressure is 20 psi
.
Care and Cleaning
Clean the outside surface of your vitreous
china water closet with mild soap and warm
water. Wipe the entire surface completely dry
with a clean soft cloth. You may use soft
abrasive cleaners when necessary to clean
your water closet.
Wipe any splashes of cleaning solutions from
plastic or plated surfaces immediately. Use
water closet cleaners on the inside of the bowl
only.
If the vitreous china surface becomes
excessively dirty, use a general purpose
cleaner such as: Fantastic, Basin Tub and Tile
Cleaner, Soft Scrub, Disinfectant Bathroom
Cleaner, Spic and Span Liquid, Scrubbing
Bubbles, or Bon Ami. Over time, hard water
deposits may clog water closet rim bowl rinse
holes and trapways. To clean, use a
commercial cleaner that is recommended for
removing hard water deposits. Follow the
cleaner manufacturer’s instructions for use.
Mirabelle shall not be responsible or liable
for any tank fitting damage caused by the use
of cleaners containing chlorine (calcium
hypochlorite).
CAUTION
Risk of product damage.
DO NOT
use strong abrasive cleaners, as
they will scratch and dull the surface.
WARNING
Risk of property or product damage.
DO NOT
use in-tank cleaners in your
water closet. Products containing chlorine
(calcium hypochlorite) can seriously
damage fittings in the tank. This damage
can cause leakage and property damage.
• Periodically check for leaks for several days
following the installation.
• Adjust tank water level to the proper
marked waterline by rotating threaded rod
clockwise to raise water level or
counterclockwise to lower water level.
• Carefully set cover onto tank.
• Open supply shut-off valve slowly to check
for leaks. If the connections have been
properly assembled, a slight tightening of
the nuts should stop any leakage.
• Install toilet seat according to the packed
instructions.
Attention Installer:
Recommended water pressure is 20 psi.
Care and Cleaning
Clean the outside surface of your vitreous
china water closet with mild soap and warm
water. Wipe the entire surface completely dry
with a clean soft cloth. You may use soft
abrasive cleaners when necessary to clean
your water closet.
cleaner such as: Fantastic, Basin Tub and Tile
Cleaner, Soft Scrub, Disinfectant Bathroom
Cleaner, Spic and Span Liquid, Scrubbing
Bubbles, or Bon Ami. Over time, hard water
deposits may clog water closet rim bowl rinse
holes and trapways. To clean, use a
commercial cleaner that is recommended for
removing hard water deposits. Follow the
cleaner manufacturer’s instructions for use.
Mirabelle shall not be responsible or liable
for any tank fitting damage caused by the use
of cleaners containing chlorine (calcium
hypochlorite).
Wipe any splashes of cleaning solutions from
plastic or plated surfaces immediately. Use
water closet cleaners on the inside of the bowl
only.
If the vitreous china surface becomes
excessively dirty, use a general purpose
• Flush toilet several times and check all
connections for leaks.
• Connect supply shut-off valve to toilet
supply shank.
4. COMPLETE THE INSTALLATION
5. CONFIRM OPERATION
IMPORTANT CONSUMERR INFORMATION
5
6
• Install trip lever. Follow instructions packed
with the trip lever.
• Connect supply shut-off valve to toilet
supply shank.
• Open supply shut-off valve slowly to check
for leaks. If the connections have been
properly assembled, a slight tightening of
the nuts should stop any leakage.
• Install toilet seat according to the packed
instructions.
• Adjust tank water level to the proper
marked waterline by rotating threaded rod
clockwise to raise water level or
counterclockwise to lower water level.
• Carefully set cover onto tank.
Tubing
Ferrule
Supply shank
Tank
Seal washer
Tubing
Ferrule
Fill valve nut
Supply shut-off
valve
Compression
nut
Compression
nut
Coupling
nut
Comp.
washer
Coupling
nut
Waterline
Filter
screen
Remove tape before
flushing.
Adjust water
level
Washer
Waterline
Filter
screen
Cap
Trip
lever
Fill valve
Locknut
Nut
Hose
Flapper
Seal
Flush
valve
Nut
Clip
5. CONFIRM OPERATION
• Flush toilet several times and check all
connections for leaks.
• Periodically check for leaks for several days
following the installation.
Attention Installer:
Recommended water pressure is 20 psi
.
Care and Cleaning
Clean the outside surface of your vitreous
china water closet with mild soap and warm
water. Wipe the entire surface completely dry
with a clean soft cloth. You may use soft
abrasive cleaners when necessary to clean
your water closet.
Wipe any splashes of cleaning solutions from
plastic or plated surfaces immediately. Use
water closet cleaners on the inside of the bowl
only.
If the vitreous china surface becomes
excessively dirty, use a general purpose
cleaner such as: Fantastic, Basin Tub and Tile
Cleaner, Soft Scrub, Disinfectant Bathroom
Cleaner, Spic and Span Liquid, Scrubbing
Bubbles, or Bon Ami. Over time, hard water
deposits may clog water closet rim bowl rinse
holes and trapways. To clean, use a
commercial cleaner that is recommended for
removing hard water deposits. Follow the
cleaner manufacturer’s instructions for use.
Mirabelle shall not be responsible or liable
for any tank fitting damage caused by the use
of cleaners containing chlorine (calcium
hypochlorite).
CAUTION
Risk of product damage.
DO NOT
use strong abrasive cleaners, as
they will scratch and dull the surface.
WARNING
Risk of property or product damage.
DO NOT
use in-tank cleaners in your
water closet. Products containing chlorine
(calcium hypochlorite) can seriously
damage fittings in the tank. This damage
can cause leakage and property damage.
• Periodically check for leaks for several days
following the installation.
• Adjust tank water level to the proper
marked waterline by rotating threaded rod
clockwise to raise water level or
counterclockwise to lower water level.
• Carefully set cover onto tank.
• Open supply shut-off valve slowly to check
for leaks. If the connections have been
properly assembled, a slight tightening of
the nuts should stop any leakage.
• Install toilet seat according to the packed
instructions.
Attention Installer:
Recommended water pressure is 20 psi.
Care and Cleaning
Clean the outside surface of your vitreous
china water closet with mild soap and warm
water. Wipe the entire surface completely dry
with a clean soft cloth. You may use soft
abrasive cleaners when necessary to clean
your water closet.
cleaner such as: Fantastic, Basin Tub and Tile
Cleaner, Soft Scrub, Disinfectant Bathroom
Cleaner, Spic and Span Liquid, Scrubbing
Bubbles, or Bon Ami. Over time, hard water
deposits may clog water closet rim bowl rinse
holes and trapways. To clean, use a
commercial cleaner that is recommended for
removing hard water deposits. Follow the
cleaner manufacturer’s instructions for use.
Mirabelle shall not be responsible or liable
for any tank fitting damage caused by the use
of cleaners containing chlorine (calcium
hypochlorite).
Wipe any splashes of cleaning solutions from
plastic or plated surfaces immediately. Use
water closet cleaners on the inside of the bowl
only.
If the vitreous china surface becomes
excessively dirty, use a general purpose
• Flush toilet several times and check all
connections for leaks.
• Connect supply shut-off valve to toilet
supply shank.
4. COMPLETE THE INSTALLATION
5. CONFIRM OPERATION
IMPORTANT CONSUMERR INFORMATION
5
6
• Install trip lever. Follow instructions packed
with the trip lever.
• Connect supply shut-off valve to toilet
supply shank.
• Open supply shut-off valve slowly to check
for leaks. If the connections have been
properly assembled, a slight tightening of
the nuts should stop any leakage.
• Install toilet seat according to the packed
instructions.
• Adjust tank water level to the proper
marked waterline by rotating threaded rod
clockwise to raise water level or
counterclockwise to lower water level.
• Carefully set cover onto tank.
Tubing
Ferrule
Supply shank
Tank
Seal washer
Tubing
Ferrule
Fill valve nut
Supply shut-off
valve
Compression
nut
Compression
nut
Coupling
nut
Comp.
washer
Coupling
nut
Waterline
Filter
screen
Remove tape before
flushing.
Adjust water
level
Washer
Waterline
Filter
screen
Cap
Trip
lever
Fill valve
Locknut
Nut
Hose
Flapper
Seal
Flush
valve
Nut
Clip
5. CONFIRM OPERATION
• Flush toilet several times and check all
connections for leaks.
• Periodically check for leaks for several days
following the installation.
Attention Installer:
Recommended water pressure is 20 psi
.
Care and Cleaning
Clean the outside surface of your vitreous
china water closet with mild soap and warm
water. Wipe the entire surface completely dry
with a clean soft cloth. You may use soft
abrasive cleaners when necessary to clean
your water closet.
Wipe any splashes of cleaning solutions from
plastic or plated surfaces immediately. Use
water closet cleaners on the inside of the bowl
only.
If the vitreous china surface becomes
excessively dirty, use a general purpose
cleaner such as: Fantastic, Basin Tub and Tile
Cleaner, Soft Scrub, Disinfectant Bathroom
Cleaner, Spic and Span Liquid, Scrubbing
Bubbles, or Bon Ami. Over time, hard water
deposits may clog water closet rim bowl rinse
holes and trapways. To clean, use a
commercial cleaner that is recommended for
removing hard water deposits. Follow the
cleaner manufacturer’s instructions for use.
Mirabelle shall not be responsible or liable
for any tank fitting damage caused by the use
of cleaners containing chlorine (calcium
hypochlorite).
CAUTION
Risk of product damage.
DO NOT
use strong abrasive cleaners, as
they will scratch and dull the surface.
WARNING
Risk of property or product damage.
DO NOT
use in-tank cleaners in your
water closet. Products containing chlorine
(calcium hypochlorite) can seriously
damage fittings in the tank. This damage
can cause leakage and property damage.
• Periodically check for leaks for several days
following the installation.
• Adjust tank water level to the proper
marked waterline by rotating threaded rod
clockwise to raise water level or
counterclockwise to lower water level.
• Carefully set cover onto tank.
• Open supply shut-off valve slowly to check
for leaks. If the connections have been
properly assembled, a slight tightening of
the nuts should stop any leakage.
• Install toilet seat according to the packed
instructions.
Attention Installer:
Recommended water pressure is 20 psi.
Care and Cleaning
Clean the outside surface of your vitreous
china water closet with mild soap and warm
water. Wipe the entire surface completely dry
with a clean soft cloth. You may use soft
abrasive cleaners when necessary to clean
your water closet.
cleaner such as: Fantastic, Basin Tub and Tile
Cleaner, Soft Scrub, Disinfectant Bathroom
Cleaner, Spic and Span Liquid, Scrubbing
Bubbles, or Bon Ami. Over time, hard water
deposits may clog water closet rim bowl rinse
holes and trapways. To clean, use a
commercial cleaner that is recommended for
removing hard water deposits. Follow the
cleaner manufacturer’s instructions for use.
Mirabelle shall not be responsible or liable
for any tank fitting damage caused by the use
of cleaners containing chlorine (calcium
hypochlorite).
Wipe any splashes of cleaning solutions from
plastic or plated surfaces immediately. Use
water closet cleaners on the inside of the bowl
only.
If the vitreous china surface becomes
excessively dirty, use a general purpose
• Flush toilet several times and check all
connections for leaks.
• Connect supply shut-off valve to toilet
supply shank.
4. COMPLETE THE INSTALLATION
5. CONFIRM OPERATION
IMPORTANT CONSUMERR INFORMATION
4. COMPLETE THE INSTALLATION
5. CONFIRM OPERATION
IMPORTANT CONSUMER INFORMATION
Attention Installer:
Recommended water pressure is 20 psi.
Care and Cleaning:
Clean the outside surface of your vitreous
china water closet with mild soap and warm
water. Wipe the entire surface completely
dry with a clean soft cloth. You may use soft
abrasive cleaners when necessary to clean your
water closet.
Wipe any splashes of cleaning solutions from
plastic or plated surfaces immediately. Use
water closet cleaners on the inside of the bowl
only.
If the vitreous china surface becomes
excessively dirty, use a general purpose
cleaner such as: Fantastic, Basin Tub and Tile
Cleaner, Soft Scrub, Disinfectant Bathroom
Cleaner, Spic and Span Liquid, Scrubbing
Bubbles, or Bon Ami. Over time, hard water
deposits may clog water closet rim bowl rinse
holes and trapways. To clean, use a commercial
cleaner that is recommended for removing
hard water deposits. Follow the cleaner
manufacturer’s instructions for use.
Mirabelle shall not be responsible or liable for
any tank fitting damage caused by the use of
cleaners containing chlorine (calcium
hypochlorite).
• Open supply shut-off valve slowly to check
for leaks. If the connections have been
properly assembled, a slight tightening of
the nuts should stop the leakage.
• Install toilet seat according to the packed
instructions.
• Adjust tank water level to the proper marked
waterline by rotating threaded rod clockwise
to raise water level or counterclockwise to
lower water level.
• Carefully set cover onto tank.
• Periodically check for leaks for several days
following the installation.
• Flush toilet several times and check all
connections for leaks.
• Connect supply shut-off valve to toilet
supply shank.
6
5
Risk of product damage.
DO NOT
use strong abrasive cleaners, as
they will scratch and dull the surface.
Risk of property or product damage.
DO NOT
use in-tank cleaners in your
water closet. Products containing chlorine
(calcium hypochlorite) can seriously damage
fittings in the tank. This damage can cause
leakage and property damage.
CAUTION
CAUTION
