manualshive.com logo in svg

Mipex MIPEX-02 Series, Руководство пользователя, Страница: 37 / 46

Поделиться
Скачать
Mipex MIPEX-02 Series Скачать руководство пользователя страница 37

 

Optosense LLC 

USER MANUAL 

Design department 

SMALL-SIZE EXPLOSIVE GAS MEASURING 

SENSOR MIPEX-02-X-X-X.1 X (RX) 

 

ESAT.413347.005 UM 

Revision 3.0 

January 19th, 2017 

Page 37 of 46 

THE SOLE PROPERTY OF OPTOSENSE LLC. ANY REPRODUCTION WITHOUT THE WRITTEN PERMISSION OF OPTOSENSE LLC IS PROHIBITED. 

 

Request syntax 

USER 

mode 

OEM 

mode 

Response description 

Command description 

INDSIG OFF 

no 

yes 

OFF 

Turns  off  displaying  of 
sensor  status  with  nega-
tive  values  in  concentra-
tion field. 

INDSIG ON 

no 

yes 

ON 

Turns  on  displaying  of 
sensor  status  with  nega-
tive  values  in  concentra-
tion field (see Table 13). 

USERDATA? 

yes 

yes 

Contains 

59 

bytes 

of 

information 

and 

“0D” 

symbol. 

Returns 

all 

the 

ten 

numbers 

contained 

in 

user  section  of  sensor 
memory  separated  from 
each  other  with  “0D” 
symbol. 

USERDATAXX? 

yes 

yes 

Contains 

5 

bytes 

of 

information 

and 

“0D” 

symbol 

Returns 

a 

number 

contained 

in 

cell 

XX 

(00…09)

 

of

 

sensor 

memory user section. 

USERDATAXX YYYYY 

no 

yes 

USERDATAXX YYYYY OK 

Writes  a  number 

YYYYY

 

(00000…99999)  to  cell 

XX

  (00...09)  of  sensor 

memory user section.  

 

Table 13. Negative values in concentration field while "INDSIG" mode is on 

Concentration 

value in ASCII 

format 

Concentration 

value in hex 

format 

Status word 

compliance  

(see Table 18) 

Description 

Recommendations 

-0001 

8001 

10 

Sensor  is  warming  up. 
After  power  up,  meas-
ured 

concentration 

value  is  displayed  after 
40 s, but sensor metro-
logical  properties  are 
provided  only  after  120 
s.

 

Do  not  perform  span 
calibration. 

-0002 

8002 

31 

Zero  shifts  to  nega-
tive value. 

Possibility  of  condensed 
moisture 

on 

optical 

elements.  Dry  sensor. 
After drying, if this status 
lasts  longer  than  for  20 
minutes 

at 

stable 

conditions, 

perform 

zeroing  (see  Appendix 
D.1 

for 

procedure 

description). 

-0003 

8003 

24 

Dynamic 

temperature 

mode;  zero  shifts  to 
negative value.

 

Do 

not 

perform 

span 

calibration or zeroing.

 

Содержание MIPEX-02 Series















































Отзывы:

Нет отзывов