Mipex MIPEX-02 Series Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 46

Mipex MIPEX-02 Series Скачать руководство пользователя страница 46

Optosense LLC

USER MANUAL

Design department

SMALL-SIZE EXPLOSIVE GAS MEASURING

SENSOR MIPEX-02-X-X-X.1 X (RX)

ESAT.413347.005 UM

Revision 3.0

January 19th, 2017

Page 46 of 46

THE SOLE PROPERTY OF OPTOSENSE LLC. ANY REPRODUCTION WITHOUT THE WRITTEN PERMISSION OF OPTOSENSE LLC IS PROHIBITED.

Table 18. Status word values description

Status

word

Priority

level

12

Description

Recommendations

00

12 (lowest)

Normal operating mode, temperature
is static.

–

10

2

Sensor is warming up.

Do not perform span calibration.

11

3

Data request rate is more than 1 Hz.

Do not perform span calibration or
zeroing. Decrease request frequency.

21

10

Dynamic

temperature

mode

(temperature changes faster than by
0.6 °C/min).

Do not perform span calibration or
zeroing.

22

9

Dynamic

temperature

mode

(temperature changes faster than by 2
°C/min).

Do not perform span calibration or
zeroing.

24

7

Dynamic temperature mode; zero
shifts to negative value.

Do not perform span calibration or
zeroing.

30

4

One of the signal values (U

s

or U

ref

) is

lower than it is allowed

Possibility  of  condensed  moisture  on
optical  elements.  Dry  sensor.  After
drying,  if  this  status  lasts  longer  than
for  20  minutes  at  stable  conditions,
replace sensor.

31

8

Zero shifts to negative value.

Possibility  of  condensed  moisture  on
optical  elements.  Dry  sensor.  After
drying,  if  this  status  lasts  longer  than
for  20  minutes  at  stable  conditions,
perform zeroing (see Appendix D.1 for
procedure description).

40

6

Exceeding temperature limits.

Check the ambient temperature.

50

11

An  abrupt  signal  change  (due  to
feeding  a  gas  mixture  to  sensor
atmosphere)  or  increased  noise  on
sensor optical elements.

Do not perform span calibration or
zeroing.

If this status lasts longer than for 20
minutes at stable conditions, replace
sensor.

51

5

Complex status. Technological failure. Contact support for details

90

1 (highest)

Firmware

failure

(flash

memory

issues).

Contact support for details

1XX

–

Sensor

operates

in

low

power

consumption mode.

–

NOTE: If any status word value

except “00” and “21” appears, metrological properties of sensor

are not provided.

12

Sensor condition is characterized by set of status word parameters. <F> command returns only one

status word value in accordance with priority. To view all parameter values use command <DATAE2>.

«
...
44
45
46

Содержание MIPEX-02 Series















































Отзывы:

Нет отзывов