background image

5

Disclaimer: 

Minuteman disclaims liability for any 
personal injury, property, or other dam-
ages of any nature whatsoever, wheth-
er special, indirect, consequential, or 
compensatory, directly or indirectly re-
sulting from the publication, use of, ap-
plication, or reliance on this document 
or, except as expressly set forth in the 
sales contract for the machine, the op-
eration or maintenance of the E Ride. 
EXCEPT AS EXPRESSLY SET 
FORTH IN SUCH SALES CONTRACT, 
MINUTEMAN MAKES NO WARRAN-
TIES, EXPRESS OR IMPLIED, AND 
SPECIFICALLY DISCLAIMS ANY 
WARRANTY OF MERCHANTABILITY 
OR FITNESS FOR A PARTICULAR 
PURPOSE.
Minuteman disclaims and makes no 
guaranty or warranty, express or im-
plied, as to the accuracy or complete-
ness of any information published 
herein, and disclaims and makes no 
warranty that the information in this in-
struction manual will fulfill any parties' 
particular purposes or needs. While 
Minuteman believes that the informa-
tion in this manual is accurate, in the 
event that technical or typographical er-

rors exist in this manual, Minuteman re-
serves the right to make changes to 
subsequent editions of this manual 
without prior notice to the recipients of 
this edition. The reader should notify 
Minuteman if any errors in this manual 
are suspected. Minuteman does not un-
dertake to guarantee the performance 
of any individual manufacturer or sell-
er's products or services by virtue of this 
instruction manual.
In publishing and making this manual 
available, Minuteman is not undertaking 
to render professional or other services 
for or on behalf of any person or entity, 
nor is Minuteman undertaking to per-
form any duty owed by any person or 
entity to someone else. Anyone using 
this manual should rely on his or her 
own independent judgment or, as ap-
propriate, seek the advise of a compe-
tent professional in determining the 
exercise of reasonable care in any giv-
en circumstances.

Valid as of: August 2010

Minuteman International Inc.
14N845 U.S. ROUTE 20
PINGREE GROVE, IL. 60140
U.S.A.

Introduction

Содержание E Ride ER28C





















































Отзывы: