Minuteman E Ride ER28C Скачать руководство пользователя | Manualshive

Страница: 11 / 52

background image

11

Avoid moving parts. Do not wear loose jackets, shirts, or sleeves
when working on machine.

Avoid contact with battery acid. Battery acid can cause burns. When
working on or around batteries, wear protective clothing and safety
glasses. Remove metal jewelry.
Do not lay tools or metal objects on top of batteries.

Charging batteries generates explosive gasses.

Do not charge bat-

teries when open flames or sparks are present. Do not smoke.

Make sure the charger is turned off before disconnecting it from the
machine. Charge the batteries in a well-ventilated area with the bat-
tery cover removed completely.

Do not clean machine with a pressure washer.

Authorized personnel must perform repairs and maintenance. Use
Minuteman supplied replacement parts.

UNPACKING INSTRUCTIONS

Carefully unpack and inspect your E Ride Scrubber for shipping
damage. Follow unpacking instructions on shipping pallet. Each unit
has been tested and thoroughly inspected before shipment. Any
damage is the responsibility of the delivery carrier who should be
notified immediately.

This machine is battery operated and designed to operate on 36
Volts DC (6) 6-volt batteries.

The recommended batteries are rated 235Ah (Minuteman P.N.
956740).

We do not recommend mixing Amp Hour capacities. Any alternate
battery sets can be used if they are of equal physical size and
capacity.

Read this manual carefully before operating this machine.

The operator is responsible for taking care of the daily maintenance
and check ups of the machine to keep it in good working condition.
The operator must inform the service mechanic or supervisor when
scheduled maintenance is required as stated in the

MAINTENANCE

section of this manual.

Before starting, familiarize yourself with the machine and its controls
(see “Machine Overview, Front”, “Machine Overview, Rear”, “Opera-
tor Compartment”, & “Control Console” diagrams).

SAVE THESE INSTRUCTIONS

«
...
9
10
11
12
13
...
»

Содержание E Ride ER28C





















































Отзывы:

Нет отзывов

Похожие инструкции для E Ride ER28C

Бренд: TBH Страницы: 236

Бренд: U-Line Страницы: 3

Бренд: Lavorwash Страницы: 116

Бренд: VLX Страницы: 34

Бренд: RCm Страницы: 126

Бренд: jbc Страницы: 4

Бренд: Parkside Страницы: 14

Бренд: J-Tech Digital Страницы: 9

Powr-Flite Predator Automatic Scrubber 32

Бренд: Tacony Страницы: 15

Бренд: Lavor Страницы: 16

Бренд: VigilLink Страницы: 9

RootsScrub B4550C

Бренд: ROOTS Страницы: 22

Бренд: Black+Decker Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды