background image

- 8 -

MINOURA JAPAN HEAD OFFICE

MINOURA JAPAN HEAD OFFICE

MINOURA JAPAN HEAD OFFICE

MINOURA JAPAN HEAD OFFICE

MINOURA JAPAN HEAD OFFICE

1197-1 Godo, Anpachi, Gifu 503-2305 JAPAN

Fax +81-584-27-7505 / E-mail: [email protected]

http://www.minoura.jp

MINOURA NORTH AMERICAN WARRANTY CENTER (

MINOURA NORTH AMERICAN WARRANTY CENTER (

MINOURA NORTH AMERICAN WARRANTY CENTER (

MINOURA NORTH AMERICAN WARRANTY CENTER (

MINOURA NORTH AMERICAN WARRANTY CENTER (

For U.S. Residents only)

For U.S. Residents only)

For U.S. Residents only)

For U.S. Residents only)

For U.S. Residents only)

In Canada, have your local shop contact Norco Products for warranty and parts service.

In Canada, have your local shop contact Norco Products for warranty and parts service.

In Canada, have your local shop contact Norco Products for warranty and parts service.

In Canada, have your local shop contact Norco Products for warranty and parts service.

In Canada, have your local shop contact Norco Products for warranty and parts service.

1996 East Avenue, Hayward, CA 94541-5454 U.S.A.

Fax 1-510-538-5899 / E-mail : [email protected]

FOR MORE INFORMATION

Proudly made to exacting standards in Japan.

Copyright © 2004-2005  Minoura Co., Ltd.,  All Rights Reserved.

HOW TO USE THE GOVERNOR

(Fig. P)

Your resistance unit has already been adjusted precisely in our factory.

Adjusting the Governor is an option and not always necessary.

Your initial position is indicated by a triangle decal.  The combination of

the orange tip of the decal and the small triangle indicator on the Governor

is your initial setting (see Fig. P).

If you want to adjust the starting speed of the resistance and change it to be

higher or lower to suit your workout, you can do so by pushing down the

Governor ring and rotating, then releasing the ring.

If you increase the inside spring tension by turning the Governor to the direction of clockwise, the starting speed

will become higher.

If you loosen the spring tension by turning the Governor to the direction of counter-clockwise, the startting speed

will become lower.

CAUTION ON YOUR FLOOR PROTECTION

If you train on a carpeted surface, consider using a rubber mat or a mat of other non-marking material to eliminate

the possibility of marking the carpet by the trainer, bike, or bodily fluids. Minoura cannot be held responsible for

any stain incurred while using a Minoura product.

Minoura warrants this trainer to be free of defects in workmanship and materials for two years from the

date of purchase. This warranty is valid for the original owner only and does not apply to trainers

purchased used or trainers purchased NEW or USED through any auction site.

A copy of the original sales receipt may be required for warranty service. Please see your local shop for

details or contact Minoura directly.

Содержание E-RDA-1050R-POWERMATIC









Отзывы: