manualshive.com logo in svg

MINOLTA-QMS magicolor 2300 DL, Руководство пользователя

Поделиться
Скачать
MINOLTA-QMS magicolor 2300 DL Скачать руководство пользователя страница 110

 Status, Error, and Service Messages

102

Error Messages

This message...

means...

do this...

NO TONER UNIT X

The 

COLOR

 toner 

cartridge is not 
installed properly.

Install the indicated 
toner cartridge.

COVER OPEN
TRAY 2

The right door of 
Tray 2 is open.

Close the side cover.

DRAWER OPEN
TRAY 2

The media tray is 
not fully inserted into 
Tray 2.

Insert the media tray into 
the media feed unit.

DRUM CARTRIDGE
NOT ATTACHED

The OPC drum 
cartridge is not 
installed.

Install the drum 
cartridge.

DUPLEX UNIT
NOT ATTACHED

Duplex printing was 
specified with the 
printer driver, but the 
duplex unit is not 
attached to the 
printer.

Stop the print job, and 
then either change the 
printer driver setting or 
attach the duplex unit to 
the printer.

ERROR
MEMORY OVER FLOW

The printer has 
received more data 
than can be 
processed by its 
internal memory.

Turn the printer off, and 
then, after a few 
seconds, turn it on 
again. Decrease the 
amount of data to be 
printed (for example, by 
decreasing the 
resolution), and then try 
printing again.

Otherwise, install an 
optional memory 
module.

ERROR
VIDEO UNDER RUN

The amount of data to 
be printed exceeds 
the printer's internal 
data transmission 
speed.

Turn the printer off, and 
then, after a few 
seconds, turn it on 
again. Decrease the 
amount of data to be 
printed (for example, by 
decreasing the 
resolution), and then try 
printing again.

Содержание magicolor 2300 DL













































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды