background image

Minibar Systems 
SmartFridge 65 Solid Door – Electronics on Door 

 

 

 

DOC0118_SmartFridge 65 Solid Door - Electronics on Door_Rev-5.doc 

 

Page 6

 

QUICK COOL

 – The SmartFridge will chill until the temperature reaches 34°F/1°C. You can enter this mode 

by pressing the QUICK COOL button from ON or SNOOZE modes. The green LED will flash until QUICK 
COOL is complete. Upon completion, the SmartFridge will return to the ON mode. The default temperature 
is 34°F/1°C ± 1°C. 

DEFROST

 – The SmartFridge shuts down the compressor every 12 hours for 30 minutes to allow for frost 

and ice built up on the chiller plate to melt. This is an automatic function that runs all the time unless in STOP 
and FAILURE modes. 

FAILURE

  –  If the SmartFridge  detects  a temperature probe malfunction, the LEDs and display flash, 

displaying “EL” or “EH.” Once the problem is fixed, the unit will return to the previous mode. 

5.4

 

Special Features  

-

 

To reduce thrashing of the compressor, there is a 3-minute turn-on delay. 

-

 

Opening the door from OFF mode will switch the SmartFridge to ON mode. 

-

 

The display will dim after 10 seconds of non-use. 

-

 

A GONG (Go/No Go) test is executed at power up. All the LEDs flash, and all the segments rotate on the 
display including the decimal points. The temperature probe is checked for a valid range or connection. 

-

 

If the temperature probe is out of range or not connected the SmartFridge will go to a FAILURE mode. 

-

 

The default operating temperature is 37°F/3°C. You can change the default temperature by pressing the 
SNOOZE and QUICK COOL buttons at the same time and holding for three seconds. Both LEDs will turn 
on signifying you are in the Temperature Set mode. The current temperature setting saved in FLASH will 
be displayed. Pressing the SNOOZE button will increase the temperature, pressing the QUICK COOL 
button will decrease temperature. Press the SNOOZE and QUICK COOL buttons at the same time to exit 
Temperature  Set mode. At this time the new temperature setting will be saved in FLASH. Minimum 
temperature allowed is 34°F/1°C and maximum is 48°F/9°C. 

-

 

The temperature format can be switched between °F and °C by pressing and holding the QUICK COOL 
button for three seconds. 

Содержание SmartFridge 65












Отзывы: