manualshive.com logo in svg

Minebea OPT-563B, Краткое руководство пользователя

Поделиться
Скачать
Minebea OPT-563B Скачать руководство пользователя страница 17

 

15 

3-3-6. 

Zero Calibration 

Register the input at the zero point. 

To calibrate by entering the torque value for the torque transducer, press the 

  key and then press 

the  

key. 

Calibrate zero by entering the zero point torque (frequency) for the torque transducer. 
 
 

Calibration by entering the torque value for the torque 
transducer 

Press the 

  key to display 

  in the 

lower display, and then press the 

  key to display the 

value. 
 
The value displayed will be the output frequency for the 
torque transducer at the initial torque state previously 
registered. 
 
Set the torque value (frequency) corresponding to the zero 
point in 1 Hz intervals. 
 
* Enter the torque calibration value zero frequency 
included on the calibration certificate sheet for the torque 
transducer. 
 
 
* Enter value (4) on the calibration certificate sheet. (No 
decimal point) 
 
For example, if the torque calibration value (zero) is   
9.957 kHz, set to [9957]. 

 

 : Alters the value of the digit to be altered. 

 

 : Selects the digit to be altered. 

 

 : Cancels the setting and returns to   

   

measurement 

mode. 

 

 : Registers the value displayed and   

 

 

  proceeds to the next step. 

Press the 

  key after setting. 

 
Zero calibration error display 

 
: The display flashes for approximately 2 seconds when the torque transducer   
  frequency output is less than 9,500 Hz or if the value entered is less than 9,500 Hz.
 
: The display flashes for approximately 2 seconds when the torque transducer   
  frequency output exceeds 10,500 Hz or if the value entered exceeds 10,500 Hz. 

 

 

 

To span calibration 

Hz 

Registered torque transducer output   
value 

Hz 

Set torque transducer output value 

Содержание OPT-563B































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды