background image

To hold and mount these batteries, you can purchase a holder with 
LEGO mounts as shown here from the 

mindsensors.com

 website.

Rechargeable battery Pack 
designed for PiStorms. 

This  

battery pack comes with a 
charging adapter.

You can order it here: 

http://www.mindsensors.com/products/174-rechargeable-
battery-pack

8.4 V Li-Ion battery or 
9.6Volts Ni-CD or Ni-
MH RC rechargeable 
battery.
You can buy such 
battery and it’s charger 
in local toy store.

Mounting PiStorms on your contraption

The PiStorms fits directly on to the GPIO 
header pins of the Raspberry Pi. The 
PiStorms Frame allows users to connect 
LEGO parts. The PiStorms Frame has holes 
that are compatible with LEGO mindstorms 
products. 

PiStorms Frame Assembly Instructions

Architecture Highlights 

PiStorms has two banks for motor and sensor ports (Bank-A 
and Bank-B).  Each bank has its own I2C address. Each bank 
has two EV3 motor ports and 2 sensor ports. (Total 4 motors 
and 4 sensor ports. You can also connect NXT motors in the 
motor ports and supported NXT Sensors in the sensor ports).

PiStorms has one button/switch. The button must be pressed 
once upon start up to establish connection to the Raspberry 
Pi. You can also shutdown the Raspberry Pi by holding the 
button for approximately 10 seconds.

PiStorms is equipped with a 2.4 inch LCD touchscreen.

PiStorms has 1 LED (located in the corner of bank A for newer 
models and bank B for older models) that when programming, 
can be accessed from either bank. 

Copyright © 2016  mindsensors.com

 2/6

Содержание PiStorms







Отзывы: