background image

 

What is NXTMMX-v2

NXTMMX is a multiplexer to 
control additional NXT (or 
EV3) Motors from your NXT 
or EV3.

Connections and Placement

NXTMMX can be connected to any of the four sensor ports of NXT 
or EV3 by using standard cables from NXT set, or FlexiCable from 
mindsensors.com.
Connect your motors to ports specified as M1 and M2. 
Connect NXT or EV3 to port specified as  ‘NXT’. 
Additional Digital Sensors (or another NXTMMX) can be connected 
to port specified as ‘Sensor’. 

NOTE

Port specified as ‘Sensor’ on NXTMMX only supports I2C or Digital 
sensors or multiplexers. 
If you intend to daisy chain several NXTMMX’s or other digital 
sensors, please read the relevant section from the Advanced 
Information Appendix of this doc.

Mounting NXTMMX on your contraption

The holes on the NXTMMX enclosure are designed for 
tight fit of Technic pins (or axles) with ‘

’ cross section. 

The holes however are not designed for repeated 
insertions/removals of these pins.

To mount NXTMMX on your contraption we suggest that you use two 
dark gray ‘Technic Axle 3 with Stud’ as shown.
Insert axles from the top of the device and secure with a bushing on 
the back or mount it on your contraption directly.
Alternately, you may use blue ‘Technic Axle Pin with 
Friction’, as shown.
While disassembling contraption, leave the pins on the device.

Supplying power to your NXTMMX

The NXTMMX has Green terminals to connect external battery.

Copyright © 2016  mindsensors.com

 1/14

NXTMMX-v2 

User Guide 

Содержание NXTMMX-v2















Отзывы: