background image

Unconditional Warranty

A. Warranty

Minarik Corporation (referred to as "the Corporation") warrants that its products will be
free from defects in workmanship and material for twelve (12) months or 3,000 hours,
whichever comes first, from date of manufacture thereof. Within this warranty period, the
Corporation will repair or replace, at its sole discretion, such products that are returned to
Minarik Corporation, 901 East Thompson Avenue, Glendale, CA 91201-2011 USA.

This warranty applies only to standard catalog products, and does not apply to specials.
Any returns for special controls will be evaluated on a case-by-case basis. The
Corporation is not responsible for removal, installation, or any other incidental expenses
incurred in shipping the product to and from the repair point.

B. Disclaimer

The provisions of Paragraph A are the Corporation's sole obligation and exclude all other
warranties of merchantability for use, express or implied. The Corporation further
disclaims any responsibility whatsoever to the customer or to any other person for injury
to the person or damage or loss of property of value caused by any product that has
been subject to misuse, negligence, or accident, or misapplied or modified by
unauthorized persons or improperly installed.

C. Limitations of Liability

In the event of any claim for breach of any of the Corporation's obligations, whether
express or implied, and particularly of any other claim or breech of warranty contained in
Paragraph A, or of any other warranties, express or implied, or claim of liability that
might, despite Paragraph B, be decided against the Corporation by lawful authority, the
Corporation shall under no circumstances be liable for any consequential damages,
losses, or expense arising in connection with the use of, or inability to use, the
Corporation's product for any purpose whatsoever.

An adjustment made under warranty does not void the warranty, nor does it imply an
extension of the original 12-month warranty period. Products serviced and/or parts
replaced on a no-charge basis during the warranty period carry the unexpired portion of
the original warranty only.

If for any reason any of the foregoing provisions shall be ineffective, the Corporation's
liability for damages arising out of its manufacture or sale of equipment, or use thereof,
whether such liability is based on warranty, contract, negligence, strict liability in tort, or
otherwise, shall not in any event exceed the full purchase price of such equipment.

Any action against the Corporation based upon any liability or obligation arising
hereunder or under any law applicable to the sale of equipment or the use thereof, must
be commenced within one year after the cause of such action arises.

Содержание XL1100A









































































Отзывы: