Minarik MMRG Series страница 50 Скачать руководство пользователя

Страница: 50 / 60

Troubleshooting

Line fuse does not blow,
but the motor does not
run.

1. Speed adjust

potentiometer or
reference voltage is
set to zero speed.

2. Speed adjust

potentiometer or
reference voltage is
not connected to
drive input properly;
connections are
open.

3. INHIBIT terminals are

jumpered.

4. S2 is shorted to S0.

5. Drive is in current

limit.

6. Drive is not receiving

AC line voltage.

7. Motor is not

connected.

1. Increase the speed

adjust potentiometer
setting or reference
voltage.

2. Check connections to

input. Verify that
connections are not
open.

3. Remove jumper from

the INHIBIT
terminals.

4. Remove short.

5. Verify that motor is

not jammed.
Increase FORWARD
TORQUE or
REVERSE TORQUE
setting if they are set
too low.

6. Apply AC line voltage

to L1 and L2.

7. Connect motor to A1

and A2.

Problem

Possible
Causes

Содержание MMRG Series





























































Результаты поиска

Содержание MMRG Series

Отзывы:

Похожие инструкции для MMRG Series

Бренды по названию

Популярные бренды

Minarik MMRG Series, Руководство пользователя

Результаты поиска

Содержание MMRG Series

Отзывы:

Похожие инструкции для MMRG Series

Бренды по названию

Популярные бренды