MIMAKI CG-100SR2 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 68

MIMAKI CG-100SR2 Скачать руководство пользователя страница 41

40

Cut Out Data with Registration Mark

No-plotting area around the registration marks

An area around a registration mark (from the mark origin to the mark size area) is a non-plotting area. There
must be no data plotted or stain in this area; otherwise, a wrong origin may be detected or a mark read error
can occur.

Example of cause of wrong detection 1

There is a line outside the registration marks

Example of cause of wrong detection 2

The distance between registration marks
(TP2 and TP1 or TP4 and TP2) is smaller
than the mark length (for Type 2)

• If a wrong mark origin is detected, the cutting will be performed in a wrong area.

Mark size

Mark Form : Type 1

No-plotting area

Mark

Mark Origin

No-plotting area

Mark

Mark Origin

Mark Form : Type 2

No-plotting area

Mark Origin

Detected wrong

mark origin

Space larger than

the mark length

Space larger than
the mark length

«
...
39
40
41
42
43
...
»

Содержание CG-100SR2





































































Отзывы:

Нет отзывов