MIMAKI CG-100SR2 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 68

MIMAKI CG-100SR2 Скачать руководство пользователя страница 37

36

Cut Out Data with Registration Mark

Making sticker with a register mark (When using FineCut)

Create registration marks on an output image that you want to make a seal, and then the plotter detects
them to cut it out.

1

Make frame around the image.

• Make frame with an attached plug-in soft

“FineCut”

2

Make register mark.

• Make register mark at corners of image.
• Cutting start position is settled according to

the register mark.

• Use “FineCut” to make a register mark.
• Refer to P.39 to P.42 for the limitation of

making a register mark.

3

Print the image with register mark.

4

Load the sheet to CG-SRII.

• Refer to P.23 for loading the sheet.

5

Send the data with “FineCut” from
computer, and cut.

• For the operation of plug-in software FineCut, refer to the operation manual provided with a

FineCut CD-ROM.

Frame is attached
around the image.

Click frame

extraction button.

Regismter mark is
created at corners

of image

Click register mark

creation button.

«
...
35
36
37
38
39
...
»

Содержание CG-100SR2





































































Отзывы:

Нет отзывов