4
To indicate low battery level, the laser beams will
blink quickly 3 times, followed by 4 seconds of solid
on (repeating). Charge the battery.
• Use the embedded magnets to secure the laser
level to framing steel studs, steel beams, etc.
•
Mounting/Adjusting the Laser Level
The adjustable clearance bracket can be used to
mount the laser level in multiple ways:
•
•
Use the keyhole slot to hang the laser level on the
wall with a nail or screw.
Position the laser and/or wall mount on a stable
surface.
•
Adjustable Clearance Bracket
Hold the bracket and adjust the laser up or down until
the desired clearance is achieved.
1.
2. Lift the rubber cover to expose the micro USB port.
Insert the micro USB plug into the micro USB port.
Users may experience longer charge times from
laptops and other power sources.
3. The indicator light will display the charging status:
Pulsing Red: Charging, 0-49% charged
Pulsing Yellow: Charging, 50-99% charged
Solid Green: 100% Charged.
To charge the battery with laser in use, follow
steps1-2 listed in the section above. The indicator
light will display the charging status:
Pulsing Red (Continuous)
Upon removal of USB cable, fuel gauge will dis-
play current battery life.
WARNING
To
age,
reduce
securely
the risk of
mount/attach
injury or dam
the
-
laser before starting an operation. Injury/damage
may occur if the laser falls.
WARNING
To reduce the risk of injury or ex-
plosion, never burn or incinerate a
battery pack even if it is damaged, dead or com-
pletely discharged. When burned, toxic fumes
and materials are created.
WARNING
injury, and product damage due to
a short circuit, never immerse your tool, battery
as seawater, certain industrial chemicals, and
bleach or bleach containing products, etc., can
cause a short circuit.
Maintenance and Storage
Do not expose your battery or cordless tools to
water or rain, or allow them to get wet. This could
damage the tool and battery. Do not use oil or
solvents to clean or lubricate your battery. The
plastic casing will become brittle and crack, causing
a risk of injury.
Store batteries at room temperature away from
moisture. Do not store in damp locations where
corrosion of terminals may occur. As with other
battery types, permanent capacity loss can result if
the pack is stored for long periods of time at high
temperatures (over 50°C (120°F)).
MILWAUKEE
®
Li-Ion batteries maintain their charge during
storage longer than other battery types. After about
a year of storage, charge the battery as normal.
BATTERY
Disposing of
MILWAUKEE
®
Li-Ion
Battery
MILWAUKEE
®
Li-Ion batteries are more
environmentally friendly than some other types of
power tool batteries. Always dispose of your battery
according to federal, state and local regulations.
Contact a recycling agency in your area for
recycling locations. Even discharged batteries
contain some energy. Before disposing, use
electrical tape to cover the terminals to prevent the
battery from shorting, which could cause a fire or
explosion.
WARNING
Use and charge only REDLITHIUM
®
USB batteries in this USB re-
chargeable tool. Other types of batteries may
cause personal injury and damage.
Inserting the Battery
1. Twist the battery cap and remove.
2. Line up the arrow on the battery with the arrow in
the compartment and fully insert the battery.
3. Replace the cap and twist to secure.
ASSEMBLY
Charging the Battery
Green Solid: 50-100% remaining
Yellow Solid: 11-49% remaining
Red Solid: 3-10% remaining
When the tool is turned on under battery power
only, the remaining battery life is indicated:
Connect your USB cable to a suitable power
source such as an AC USB wall adaptor,
computer, or car USB outlet.
To charge the battery while continuing to use the
laser, follow steps1-2 listed in the section above.
The indicator light will pulse Red indicating
charing is occurring.
When the USB cable is removed from the tool,
the fuel gauge will indicate the current charge
status of the inserted battery.
Flashing Red/Green: If the indicator light flashes
Red/Green continuously, the battery is either not
inserted correctly; too hot or too cold; or the
battery is faulty or damaged. Check that the
battery is fully seated into the bay. Remove the
battery and reinsert. If the light continues to flash
red and green, the battery may be too hot or too
cold, or damaged. Allow the battery to cool down
or warm up (as appropriate) and then reinsert. If
the problem persists, contact a
MILWAUKEE
®
service facility.
Use the ¼" - 20 threaded insert to mount on a
standard tripod with a corresponding mounting
point.
WARNING
To reduce the risk of injury or tem-
look directly into the laser when it is on.
CAUTION
Use of controls or adjustments or
performance of procedures other
-
ous radiation exposure.
NOTICE
Perform the Accuracy Field Check
procedure immediately upon unboxing
of each new Laser Level and before exposure to
jobsite conditions. See "Accuracy Field Check"
for information.
OPERATION
