Milwaukee M12 SI, Оригинальное руководство пользователя

Страница: 7 / 9

12 13
M12 SI
...........................90 W
.........................400 °C
...........................18 s
...........................12 V
........................0,41 kg
.................-18...+50 °C
......................... M12B...
...........................M12...
ENGLISH
2012/3032 (as amended) and that the following designated
standards have been used:
BS EN 60335-1:2012+A13:2017
BS EN 60335-1:2012+A13:2017
BS BS EN 60335-2-45:2002+A2:2012
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN EC 63000:2018
Winnenden, 2020-31-20
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
• The user can transport the batteries by road without
further requirements.
• Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be
carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement
within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Please read the instructions carefully before
starting the machine.
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached the
end of their life must be collected separately and
returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
Caution – hot surfaces!
Always wear eye protection!
European Conformity Mark
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
TECHNICAL DATA SOLDERING IRON
Average Heater Power (max) .................................................
Set Tip Temperature ...............................................................
Warm up time .........................................................................
Battery voltage........................................................................
Weight according EPTA-Procedure 01/2014 (2,0 Ah) ............
Recommended ambient operating temperature .....................
Recommended battery types..................................................
Recommended charger ..........................................................
Do not use battery packs from other
systems.
Battery acid may leak from damaged
batteries under extreme load or
extreme temperatures. In case of
contact with battery acid wash it off
immediately with soap and water. In
case of eye contact rinse thoroughly
for at least 10 minutes and
immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and
product damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to fl ow
inside them. Corrosive or conductive fl uids, such as
seawater, certain industrial chemicals, and bleach or bleach
containing products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The Soldering Iron is intended to be used for soldering or
tinning electrical components, cables, conductors, etc use
away from mains supply.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under “Technical Data” fulfi lls all the relevant
regulations and the directives 2011/65/EU (RoHs), 2014/30/
EU, 2006/42/EC, and the following harmonized standards
have been used:
EN 60335-1:2012+A11:2014+A11:2014+
EN 60335-1:2012+A11:2014+A11:2014+
A13:2017+A1:2019+A2:2019+A14:2019 A13:2017+A1:2019+A2:2019+A14:2019
EN 60335-2-45:2002+A1:2008+A2:2012
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN EC 63000:2018
Winnenden, 2020-31-20
Alexander Krug
Managing Director
Authorized to compile the technical fi le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility
that the product described under “Technical Data” fulfi lls all
the relevant provisions of the following Regulations S.I.
2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I.
WARNING Read these instructions carefully, be
familiar with the controls and the proper use of the
machine. Save all warnings and instructions for future
reference.
SAFETY INSTRUCTIONS SOLDERING IRON
Contact with a hot tool tip could ignite fl ammable materials.
Contact with a hot tip could ignite a fi re.
Do not stand or store tool upright on the battery pack. Tool
could tip resulting in contact between hot tip and fl ammable
materials. Always set/store tool on its side when not in use.
Keep hands and fi ngers behind fi nger guard. Serious burns
can occur if skin contacts tip.
Remove battery before storing. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
Work in well ventilated areas. Soldering can produce fumes
and smoke.
Use personal protective equipment when using chemicals,
such as fl ux and solder paste. Follow all manufacturer
instructions.
To reduce the risk wear safety goggles or glassesof injury,
always with side shields.
For changing the soldering tip ensure the tip is cool and the
tip temp indicator is off before touching the tip. Serious
burns could occur if skin contacts a hot tip.
Do not stand on battery pack (unstable).
ADDITIONAL SAFETY INSTRUCTIONS
Never allow children, persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge or people unfamiliar with
these instructions to use the machine,
local regulations may restrict the age
of the operator.
Remove the battery pack before
starting any work on the machine.
Do not dispose of used battery packs
in the household refuse or by burning
them. Milwaukee Distributors off er to
retrieve old batteries to protect our
environment.
Do not store the battery pack together
with metal objects (short circuit risk).
Use only System M12 chargers for
charging System M12 battery packs.
ENGLISH