Milwaukee DEC 125, Оригинальное руководство пользователя, Страница: 6 / 86

4
GB
English
h) The outside diameter and the thickness of your diamond
wheel must be within the capacity rating of your power
tool. Incorrectly sized diamond wheels cannot be adequately
guarded or controlled.
i) The arbour size of diamond wheels and flanges must
properly fit the spindle of the power tool.
Diamond wheels
and flanges with arbour holes that do not match the mounting
hardware of the power tool will run out of balance, vibrate excessi-
vely and may cause loss of control.
j) Do not use damaged diamond wheels. Before each use,
inspect the diamond wheels for chips and cracks, tear or
excess wear. If power tool or diamond wheel is dropped,
inspect for damage or install an undamaged diamond wheel.
After inspecting and installing the diamond wheel, position
yourself and bystanders away from the plane of the rotating
diamond wheel and run the power tool at maximum no load
speed for one minute. Damaged diamond wheels will normally
break apart during this test time.
k) Wear personal protective equipment. Depending on ap-
plication, use face shield, safety goggles or safety glasses. As
appropriate, wear dust mask, hearing protectors, gloves and
shop apron capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of stopping flying
debris generated by various operations. The dust mask or respirator
must be capable of filtrating particles generated by your operation.
Prolonged exposure to high intensity noise may cause hearing loss.
l) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal protec-
tive equipment. Fragments of workpiece or of a broken diamond
wheel may fly away and cause injury beyond immediate area of
operation.
m) Hold the power tool by insulated gripping surfaces only,
when performing an operation where the diamond wheel
may contact hidden wiring or its own cord. Diamond wheel
contacting a „live“ wire may make exposed metal parts of the power
tool „live“ and could give the operator an electric shock.
n) Position the cord clear of the spinning diamond wheel.
If you lose control, the cord may be cut or snagged and your hand or
arm may be pulled into the spinning diamond wheel.
o) Never lay the power tool down until the diamond wheel
has come to a complete stop.
The spinning diamond wheel may
grab the surface and pull the power tool out of your control.
p) Do not run the power tool while carrying it at your side.
Accidental contact with the spinning diamond wheel could snag your
clothing, pulling the diamond wheel into your body.
q) Regularly clean the power tool’s air vents. The motor’s fan
will draw the dust inside the housing and excessive accumulation of
powdered metal may cause electrical hazards.
r) Do not operate the power tool near flammable materials.
Sparks could ignite these materials.
WARNING!
Always read the operation manual of the connected angle
grinder. Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SPECIFIED CONDITIONS OF USE
The cutting guard is intended for abrasive cutting-off operations in
stone and ceramic materials with diamond wheels.
The cutting guard is suitable only for working without water.
The cutting guard must only be used with the following angle
grinders: Milwaukee AG 12-115 X, AGV 15-125 XC, AG 12-125 X,
AGV 15-125 XE, AGV 12-125 X, AGV 12-125 XPD
The cutting guard must only be used in combination with a suitable
vakuum cleaner.
CUT-OFF MACHINE SAFETY WARNINGS
Safety Warnings Common for Abrasive Cutting-Off Opera-
tions with diamond wheel:
a) This power tool is intended to function as a cut-off tool.
Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow
all instructions listed below may result in electric shock, fire and/
or serious injury.
b) Operations such as polishing, grinding, sanding and
wire brushing are not recommended to be performed with
this power tool. Operations for which the power tool was not
designed may create a hazard and cause personal injury.
c) The cutting guard must be securely attached to the
power tool and positioned for maximum safety, so the
least amount of wheel is exposed towards the operator.
The
cutting guard helps to protect the operator from broken diamond
wheel fragments and accidental contact with wheel.
d) Use only diamond cut-off wheels for your power tool.
e) The rated speed of the diamond wheel must be at least
equal to the maximum speed marked on the power tool.
Diamond wheels running faster than their rated speed can break
and fly apart.
f) Diamond wheels must be used only for recommended
applications. For example: do not grind with the side of
diamond wheel. Diamond wheels are intended for peripheral
grinding, side forces applied to these diamond wheels may cause
them to shatter.
g) Always use undamaged wheel flanges that are of correct
size and shape for your selected diamond wheel. Proper
wheel flanges support the diamond wheel thus reducing the pos-
sibility of diamond wheel breakage. Flanges for diamond wheels
may be different from grinding wheel flanges.
TECHNICAL DATA
Cutting Guard
DEC 125
Cutting disk -ø 115 / 125 mm
Cutting depth min. (ø 115 / ø 125 mm) 0 / 5 mm
Cutting depth max. (ø 115 / ø 125 mm) 23 / 28 mm
Weight 620 g